Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Forming Limit Analysis of Mg-2Zn-1.2Al-0.2Ca-0.2RE Alloy Sheet Using Ductile Fracture Models

Analytical Method for Forming Limit Diagram Prediction with Application to a Magnesium ZEK100-O Alloy

Forming Limit Diagram Analysis Based on Crystal Plasticity for Magnesium Alloy Sheets

Modeling of the Ductile Fracture During the Sheet Forming of Aluminum Alloy Considering Non-Associated Constitutive Characteristic

Predicting Sheet Forming Limit of Aluminum Alloys for Cold and Warm Forming by Developing a Ductile Failure Criterion

Analysis of Forming Limits Based on a New Ductile Damage Criterion in St14 Steel Sheets

Forming Limit Prediction of Anisotropic Aluminum Magnesium Alloy Sheet AA5052-H32 Using Micromechanical Damage Model

Forming Limits of Magnesium Alloy AZ31B Sheet at Elevated Temperatures

Forming Limit Prediction Using an Integrated Model for 7075 Aluminum Alloy Sheets at an Elevated Temperature

A continuum damage model for Mg/Al composite sheets rolling: Theoretical development and application

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Failure prediction of magnesium alloys based on improved CDM model

Stress-state dependency of ductile fracture in an extruded magnesium alloy and its underlying mechanisms

Constitutive Behavior and Forming Limit of Mg-Al-Ca-Gd Alloy Sheets at Room and Elevated Temperatures

Study on Plastic Constitutive Relation and Ductile Fracture Criterion of AM60B Magnesium Alloy

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy

Damage and forming limit analysis in porous ductile sheet metals at room or elevated temperatures

Modeling Anisotropic Ductile Fracture of AA7075-T6 Sheet for Sheet Metal Forming Considering Anisotropic Stress State

Influences of stress states and loading directions on the anisotropic fracture of magnesium alloy AZ31B sheet under tension-dominated forming conditions

Characterization of Forming Limits at Fracture for Aluminum Alloy 6K21-T4 Sheets in Non-Linear Strain Paths Using a Biaxial Tension/shear Loading Test

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy