Abstract:The present paper focuses on the heat transfer and contact pressure at the casting-die interface in squeeze casting process. Experiments were conducted and a "plate shape" was used to cast aluminum alloy A356 in H13 steel die. Based on the temperature measurements inside the die, the interfacial heat transfer coefficient (IHTC) at the metal-die interface was determined by applying an inverse approach. The pressure at the metal-die interface was measured by using Kistler pressure transducer. The acquired data were processed by a low pass filtering method based on Fast Fourier Transform (FFT). Besides, a set of methods was set up to verify the computer program for the inverse model. The results show that the pressure at the casting-die interface and the IHTC rose to the peak value almost simultaneously as soon as the pressure was applied by the press. The higher the applied pressure, the higher the peak value of the IHTC and the pressure at the casting-die interface. It was a pressure maintaining stage immediately after the pressure was applied. During this stage, the pressure at the casting-die interface decreased immediately after it reached the peak value. The IHTC sharply dropped at the beginning. Then, the decrease rate of the IHTC became lower and lower. Besides, the IHTC of the cases with pressure applied was much higher than those without pressure applied. It indicates that the applied pressure greatly improved the contact status of casting and die surfaces and reduced the thermal resistance between the two surfaces. The IHTC profiles of the cases with the pressures 23 MPa and 46 MPa applied did not make much difference, however, when the applied pressure reached 70 MPa, the influence of the pressure at the casting die interface on the IHTC became very remarkable. (C) 2017 Elsevier Ltd. All rights reserved.

Heat Treatment Conditions for High‐Performance High‐Pressure Die‐Cast Al–Si–Cu–Mg Alloy

Effect of solution treatment on blistering and microstructure of high-pressure die cast A380 alloy

Microstructure Evolution of Modified Die-Cast AlSi10MnMg Alloy During Solution Treatment and Its Effect on Mechanical Properties

Microstructural Evolution and Strengthening Behavior of High-Pressure Die-Cast High-Cu Al-Si-Cu-Mg Alloy with T5 Treatment

Rotating bending fatigue behavior of high-pressure diecast AlSi10MgMn alloy based on T5 heat treatment parameters

Effect of Heat Treatment on Microstructures and Mechanical Properties of High Vacuum Die Casting Mg–8Gd–3Y–0.4Zr Magnesium Alloy

A Study on High Strength, High Plasticity, Non-Heat Treated Die-Cast Aluminum Alloy

Study on Interfacial Heat Transfer Coefficient at Metal/die Interface During High Pressure Die Casting Process of AZ91D Alloy

Achieving High Performance by Optimized Heat Treatment in a Spray Formed Al–Zn–Mg–Cu Alloy

Effects of Alloy Materials and Process Parameters on the Heat Transfer Coefficient at Metal/Die Interface in High Pressure Die Casting

Characteristics of Al-Si Alloys with High Melting Point Elements for High Pressure Die Casting

Investigating Thermal and Mechanical Characteristics of Die-Casting Aluminum Alloys: A Comprehensive Investigation via Thermal Analysis

Experimental Study on the Heat Transfer Behavior and Contact Pressure at the Casting-Mold Interface in Squeeze Casting of Aluminum Alloy

Mechanism of cryogenic, solid solution and aging compound heat treatment of die-cast Al alloys considering microstructure variation

Microstructural Evolution and Mechanical Strengthening Mechanism of the High Pressure Heat Treatment (HPHT) on Al-Mg Alloy

Influence of the Solution and Artificial Aging Treatments on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Mg Alloys

Effect of short T6 heat treatment on the microstructure and the mechanical properties of newly developed die-cast Al–Si–Mg–Mn alloys

Determination of Interfacial Heat Transfer Behavior at the Metal/Shot Sleeve of High Pressure Die Casting Process of AZ91D Alloy

Mechanical Properties and Conductivity of Low-Pressure Die-Cast 319 Aluminum Prepared with Hot Isostatic Pressing, Thermal Treatment, or Chemical Treatment

Microstructure and Mechanical Properties of Melt-Conditioned High-Pressure Die-Cast Mg-Al-Ca Alloy

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing