Abstract:The non-heat-treated, die-cast aluminum alloy samples were prepared meticulously via die-casting technology. The crystal structure, microstructure, and phase composition of the samples were comprehensively studied through electron backscatter diffraction (EBSD), metallographic microscopy, spectrometer, and transmission electron microscopy (TEM). The microhardness and tensile properties of the samples were tested. The die-cast samples were found to have desirable properties by studying the structure and performance of the samples. There were no defects, such as pores, cold partitions, or surface cracks, found. The metallographic structure of the samples was mainly α-Al, and various phases were distributed at the grain boundaries. Before heat treating, α-Al grains were mainly equiaxed with a great number of second phase particles at the grain boundaries. After heat treating, the α-Al grains were massive and coarsened, and the second phase grains were refined and uniformly distributed, compared with those before the heat treating. The EBSD results showed that the grain boundary Si particles were solid solution decomposed after heat treatment. The particles became smaller, and their distribution was more uniform. Transmission electron microscopy found that there were nano-scale Al-Mn, Al-Cu, and Cu phases dispersed in the samples. The average microhardness of the samples before heat treating was 114 HV0.1, while, after the heat treating, the microhardness reached 121 HV0.1. The mechanical features of the samples were tremendous, and the obtained die-cast aluminum alloy had non-heat-treatment performance, which was greater than the ordinary die-cast aluminum alloys with a similar composition. The tensile strength of the aluminum alloys reached up to 310 MPa before heat treatment.

Design of Non-Heat Treatable High Pressure Die Casting Al Alloys: A Review

Microstructural Characteristics of High-Pressure Die Casting with High Strength-Ductility Synergy Properties: A Review

Research Progress on Thermal Conductivity of High-Pressure Die-Cast Aluminum Alloys

Influence of Introducing Zr, Ti, Nb and Ce Elements on Externally Solidified Crystals and Mechanical Properties of High-Pressure Die-Casting Al–Si Alloy

MELT CONDITIONED HIGH PRESSURE DIE CASTING (MC-HPDC) OF Mg-ALLOYS

A Study on High Strength, High Plasticity, Non-Heat Treated Die-Cast Aluminum Alloy

Innovative Hybrid High-Pressure Die-Casting Process for Load-Bearing Body-In-White Structural Components

Secondary Al-Si-Mg High-pressure Die Casting Alloys with Enhanced Ductility

Characteristics and distribution of microstructures in high pressure die cast alloys with X-ray microtomography: A review

Microstructure and Mechanical Properties of Melt-Conditioned High-Pressure Die-Cast Mg-Al-Ca Alloy

Microstructural Evolution and Strengthening Behavior of High-Pressure Die-Cast High-Cu Al-Si-Cu-Mg Alloy with T5 Treatment

Microstructure, Phase Formation and Heat-Treating of Novel Cast Al-Mg-Zn-Cu-Si Lightweight Complex Concentrated Aluminum Based Alloy

Relationship of Compositions, Phase Constituents and Solidification Paths of Casting Mg-Al-Zn Alloys

Towards high performance Al–Si–Fe alloy castings via rheo-diecasting: Effect of injection velocity and heat treatment on microstructure evolution and property

Characteristics of Al-Si Alloys with High Melting Point Elements for High Pressure Die Casting

Role of alloying and heat treatment on microstructure and mechanical properties of cast Al-Li alloys: A review

Investigating Thermal and Mechanical Characteristics of Die-Casting Aluminum Alloys: A Comprehensive Investigation via Thermal Analysis

Strength and ductility optimization of HPDC AlSi8MgCuZn2 alloys by modifying pre-aging treatment

Heat-resistant Al alloys: microstructural design and microalloying effect

Influence of intermetallics and element concentrations on the performance of the heat treated HVDC AlSiMgMnCu alloys at nano-scale

Alloy development and process innovations for light metals casting