Abstract:Cellular Polymers, Ahead of Print. The crystallization behavior during foaming directly affects the foaming properties. For crystalline polymers, there is no consensus on the influence of the crystallization behavior during foaming process on the stabilization of the cell structure. In this work, PBAT foamed bead and unfoamed pellets were prepared by controlling the saturated temperatures in supercritical CO2, soaking step (one or two) and the depressurization rate, respectively. Double melting peaks were observed in the DSC curve of supercritical CO2 foamed PBAT beads. By comparing the outgassing rates we find that the stretching-induced crystallization caused by the rapid expansion of the gas during foaming plays an important role in the stabilization of the cells. Although the crystalline perfection or crystal size at this time is much smaller than that of the crystalline grains formed during static cooling, the rapid crystallization is effective in stabilizing the cell structure of the foamed pores. Compared to normal supercritical foaming processes, the two-step foaming process of soaking CO2 at high temperatures followed by foaming at low temperatures results in an increase in cell size and expansion ratio. At high temperatures, more CO2 diffuses into the PBAT pellets, increasing the instantaneous gas concentration in the pellets for foaming, and the rapid stretching produces stretching-induced crystallization that raises the average size of the cells, further increasing the expansion multiplicity of individual cells. The average cell size of foam beads rises from 37.8 to 48.8 μm and the expansion ratio also increases to 8.6 with saturated temperature increasing form 95 to 105°C. The two-step soaking foaming method is a more efficient way of manufacturing industrial foamed beads, allowing for the preparation of better foam beads at low temperatures.

Tuning cellular structure in a previously developed microcellular acrylonitrile butadiene styrene/thermoplastic polyurethane blend foams

Preparation of Cellulose/MWCNTs/TPU Micro-foam Composites

Investigation into the effects of foaming variables on the cellular structure and expansion ratio of foamed TPU using response surface methodology

Tpu/Pla Blend Foams: Enhanced Foamability, Structural Stability, And Implications For Shape Memory Foams

Microcellular Thermoplastic Polyurethane (TPU) with Multimodal Cell Structure Fabricated Based on Pressure Swing Strategy and Its Compressive Mechanical Properties

Supercritical carbon dioxide foamed thermoplastic polyester elastomer with poly(lactic acid) blending: shrinkage reduction and expansion ratio improvement

Research on Microcellular ABS Foam by Compression Molding

Preparation of Low Density Microcellular Thermoplastic Polyurethane with High Compression Properties Based on Micro-Phase Separation Structure

Analysis on Gas Diffusion Behavior of ABS Microcellular Foam Material

Effect of calcium silicate on foaming and anti‐shrinkage behavior of thermoplastic polyamide elastomers: Revelation of the open‐cell mechanism

Facile Fabrication of Lightweight Shape Memory Thermoplastic Polyurethane/Polylactide Foams by Supercritical Carbon Dioxide Foaming

Structure-tunable polyether block amide/polylactic acid foams with shape memory performance using supercritical CO 2 foaming

Approach to Fabricating Thermoplastic Polyurethane Blends and Foams with Tunable Properties by Twin‐Screw Extrusion and Microcellular Injection Molding

Structure-tunable Polyether Block Amide/polylactic Acid Foams with Shape Memory Performance Using Supercritical CO2 Foaming

Multi-Response Optimization and Cell Structure-Property Relationships of Polylactide (PLA) Foams

A new microcellular foaming strategy to develop structure-gradient thermoplastic polyurethane foams with enhanced elasticity

Foaming Behaviors of Poly (butylene Adipate-Co-terephthalate) with Methyl Methacrylate-Co-glycidyl Methacrylate As Chain Extender

MMT‐St and PLA synergistically enhanced the microcellular of TPU foam and improved its dimensional stability

Synergistic effects of in situ fibrillated polytetrafluoroethylene and polystyrene–butadiene block on the microcellular foaming behaviors of polyphenylene oxide modified by high‐impact polystyrene

Microcellular PETs with High Expansion Ratio Produced by Supercritical CO2 Molding Compression Foaming Process and Their Mechanical Properties

Influence of foaming-induced crystallization behavior on the structure of poly(butylene adipate-co-terephthalate) supercritical foamed beads