Abstract:The objective of this study was to create foam from a blend of ABS/TPU (50:50 wt%) by using CO2 as a physical blowing agent. The main goal of this investigation was to determine the impact of different parameters on the expansion ratio and cell structure. This study investigates the cell structure control in 50% thermoplastic polyurethane (TPU) and 50% acrylonitrile butadiene styrene (ABS) blend foam using CO2 as a physical blowing agent, focusing on the effects of variable foaming parameters on the microstructure. Samples measuring 25 × 25 × 1 mm were produced and analyzed for foam structure. The foaming process involved saturating the samples with CO2 gas at pressures of 4, 5.5, and 7 MPa, followed by rapid pressure release and immersion in a hot glycerol bath. The foaming parameters included varied temperatures (80, 90, and 120°C) and times (5–80 s). Scanning electron microscope (SEM) analysis provided data on cell size and density. Results indicated that increasing the saturation pressure enhanced CO2 uptake in the ABS/TPU blend, with the CO2 uptake rate peaking early in the process. Higher foaming temperatures and extended foaming times led to increased cell size, cell density, and expansion ratio. These findings highlight the significant role of process parameters in controlling the cell structure of ABS/TPU blend foams, offering valuable insights into optimizing foam properties for industrial applications. Highlights Optimization of foam parameters leads to cell structure control in ABS/TPU composite foams for industrial applications. Increasing saturation pressure significantly boosts CO2 uptake in ABS/TPU composite foams. Increasing the foaming temperature and duration leads to larger cell sizes, higher cell density, and greater expansion ratios in ABS/TPU composite foams.

Research on Microcellular ABS Foam by Compression Molding

Analysis on Gas Diffusion Behavior of ABS Microcellular Foam Material

Effect of Melt Viscosity on the Cell Morphology and Properties of Poly(lactic Acid) Foams

Preparation of Cellulose/MWCNTs/TPU Micro-foam Composites

Extrusion Foaming Of Lightweight Polystyrene Composite Foams With Controllable Cellular Structure For Sound Absorption Application

Tuning cellular structure in a previously developed microcellular acrylonitrile butadiene styrene/thermoplastic polyurethane blend foams

Preparation, Characterization, and Mechanical Properties of Microcellular Poly(Aryl Ether Ketone) Foams

Preparation and Properties of Microcellular Foamed PP by New Foaming Agent

Preparation and Density Control of Pmma Microcellular Foams Via Supercritical Carbon Dioxide Foaming

Microcellular processing and relaxation of poly(ether ether ketone)

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Microcellular Injection Molded Wood Fiber-PP Composites: Part I - Effect of Chemical Foaming Agent Content on Cell Morphology and Physico-mechanical Properties

Plane-compression properties of microcellular injected polypropylene using gas counter pressure and core-back expansion process

Microcellular foams simultaneous reinforcing and toughening strategy of combining nano-fibrillation network and supercritical solid-state foaming

Microcellular Thermoplastic Polyurethanes and Their Flexible Properties Prepared by Mold Foaming Process with Supercritical CO2

Study on microcosmic properties and temperature simulation of foamed polypropylene composites

Fabrication of Open‐Cell Microcellular Acrylonitrile Butadiene Styrene Composite Foams with Enhanced Electrical Conductivity and High‐Performance Electromagnetic Interference Shielding

Effect of Stereocomplexation on High-temperature Microcellular Foaming Behaviour, Compressive Property and Heat Resistance of Branched Poly(l-lactide)/poly(d-lactide)

Multi-Response Optimization and Cell Structure-Property Relationships of Polylactide (PLA) Foams

Poly(ether imide)/Epoxy Foam Composites with a Microcellular Structure and Ultralow Density: Bead Foam Fabrication, Compression Molding, Mechanical Properties, Thermal Stability, and Flame-Retardant Properties

Microcellular injection molding of foamed engineering plastic parts with high dimensional accuracy