Abstract:Microcellular foaming with CO2 and N2 as co‐blowing agents is developed to achieve mechanically robust PEBA foams by reducing the dimensional shrinkage. Compared with pure CO2 as blowing agents, the co‐blowing agents leads to significantly reduced shrinkage of PEBA foams after foaming and hence improved mechanical performance. The promising outcome paves way for developing high‐performance thermoplastic elastomer foams. Polyether block amide (PEBA) is an important thermoplastic polyester elastomer (TPE) owing to its low density and high resilience. Microcellular foaming can endow PEBA with significant potential in sports, medical, and industrial applications. However, with the current microcellular foaming technology, it remains challenging to obtain PEBA foams with stable shapes, which are critical for their mechanical properties. Therefore, microcellular foaming with CO2 and N2 as co‐blowing agents is utilized in this study to achieve mechanically robust PEBA foams by reducing the dimensional shrinkage. The introduction of N2 can effectively slow the diffusion rate of blowing agents into the air, providing support for the foam to resist external atmospheric pressure and effectively reducing the dimensional shrinkage of PEBA foams. Consequently, a stable foam shape is achieved with an expansion ratio of 7.9. Finally, the PEBA foams with excellent shrinkage resistance and mechanical properties are prepared, and the cell shrinkage mechanism is analyzed to study the effects of blowing agents and foaming methods on the structural evolution of TPE foams. This promising outcome paves way for their practical industrial applications.

Preparation, Characterization, and Mechanical Properties of Microcellular Poly(Aryl Ether Ketone) Foams

Effect of Melt Viscosity on the Cell Morphology and Properties of Poly(lactic Acid) Foams

Microcellular processing and relaxation of poly(ether ether ketone)

Preparation of Cellulose/MWCNTs/TPU Micro-foam Composites

Microstructure of Ceramic Foams

Large Stiffness Thermoformed Open Cell Foams with Auxeticity

Highly Sensitive Large Strain Cellulose/multiwalled Carbon Nanotubes (mwcnts)/thermoplastic Polyurethane (TPU) Nanocomposite Foams: from Design to Performance Evaluation

Microstructure and Properties of Microcellular Poly (phenylene Sulfide) Foams by Mucell Injection Molding

Poly(ether imide)/Epoxy Foam Composites with a Microcellular Structure and Ultralow Density: Bead Foam Fabrication, Compression Molding, Mechanical Properties, Thermal Stability, and Flame-Retardant Properties

Preparation of Open-Cell Polymer Foams by CO2 Assisted Foaming of Polymer Blends

Compressive response and energy absorption of foam EPDM

Preparation and Density Control of Pmma Microcellular Foams Via Supercritical Carbon Dioxide Foaming

Preparation and characterization of microcellular injection molded foams from high-performance blends based on PPS-modified PPBESK

Cell Morphology And Mechanical Properties Of Microcellular Mucell (R) Injection Molded Polyetherimide And Polyetherimide/Fillers Composite Foams

Comprehensive analysis of mechanical properties of microcellular polypropylene: Experiment and simulation

Fabrication And Cell Morphology Of A Microcellular Poly(Ether Imide)-Carbon Nanotube Composite Foam With A Three-Dimensional Shape

Controlling cellular morphology by supercritical carbon dioxide

Physical Properties of Microcellular Polymeric Foams with Supercritical CO2

Research on Microcellular ABS Foam by Compression Molding

Super‐Elastic and Dimensionally Stable Polyether Block Amide Foams Fabricated by Microcellular Foaming with CO2&N2 as Co‐Blowing Agents

Fabrication of lightweight polyethersulfone foams with enhanced surface quality and high specific flexural properties using micro‐opening microcellular injection molding