Abstract:To avoid introduction of milling media during ball‐milling process and ensure uniform distribution of SiC and graphite in ZrB2 matrix, ultrafine ZrB2–SiC–C composite powders were in‐situ synthesized using inorganic–organic hybrid precursors of Zr(OPr)4, Si(OC2H5)4, H3BO3, and excessive C6H14O6 as source of zirconium, silicon, boron, and carbon, respectively. To inhabit grain growth, the ZrB2–SiC–C composite powders were densified by spark plasma sintering (SPS) at 1950°C for 10 min with the heating rate of 100°C/min. The precursor powders were investigated by thermogravimetric analysis–differential scanning calorimetry and Fourier transform infrared spectroscopy. The ceramic powders were analyzed by X‐ray diffraction, X‐ray photoelectron spectroscopy, and scanning electron microscopy. The lamellar substance was found and determined as graphite nanosheet by scanning electron microscopy, Raman spectrum, and X‐ray diffraction. The SiC grains and graphite nanosheets distributed in ZrB2 matrix uniformly and the grain sizes of ZrB2 and SiC were about 5 μm and 2 μm, respectively. The carbon converted into graphite nanosheets under high temperature during the process of SPS. The presence of graphite nanosheets alters the load‐displacement curves in the fracture process of ZrB2–SiC–G composite. A novel way was explored to prepare ZrB2–SiC–G composite by SPS of in‐situ synthesized ZrB2–SiC–C composite powders.

In-situ synthesized phases during the spark plasma sintering of g-C3N4 added TiB2 ceramics: A thermodynamic approach

In Situ Combustion Synthesis of TiB<sub>2</sub>-AIN Composites

In-situ synthesis TiC + TiB/Ti composites by spark plasma sintering

A microstructural approach to the chemical reactions during the spark plasma sintering of novel TiC–BN ceramics

Spark plasma sintering of TiN ceramics codoped with SiC and CNT

Reaction mechanism and friction behavior of an in-situ Ti/B4C composite synthesized by spark plasma sintering

Spark Plasma Sintering Reaction Synthesized Tib Reinforced Titanium Matrix Composites

Microstructures and mechanical properties of TiB2 composite ceramics with co-addition of Ti and TiC fabricated by SPS

Influence of Conductive Nano-Tic on Microstructural Evolution of Si3n4-Based Nanocomposites in Spark Plasma Sintering

In-situ synthesis of TiN and TiB2 compounds during reactive spark plasma sintering of BN–Ti composites

Densification, Microstructure, and Wear Properties of TiB2-TiC-GNP and TiB2-TiC-BN Composites

Preparation of Multi-Walled Carbon Nanotube-Reinforced TiNi Matrix Composites from Elemental Powders by Spark Plasma Sintering

Fabrication of (Zr,Ti)B2-ZrN-BN composites through reactive spark plasma sintering of ZrB2 and TiN

Reaction Sintering of Machinable TiB2-BN-C Ceramics with In-Situ Formed h-BN Nanostructure

ZrB2–SiC–G Composite Prepared by Spark Plasma Sintering of In‐Situ Synthesized ZrB2–SiC–C Composite Powders

Mechanical Alloying and Spark Plasma Sintering of Ni-Al-Ti-B Powders for Fabricating Nanocrystailine (Tib+tib2)/ni-3(Al, Ti) Composite

Ceramic Matrix Composites Obtained by the Reactive Sintering of Boron Carbide with Intermetallic Compounds from the Ti-Si System

Enhancement mechanical properties of in-situ preparated B4C-based composites with small amount of (Ti3SiC2+Si)

Novel (ti, W)C–SiC–WSi2 Ceramics Fabricated Via in Situ Reaction Spark Plasma Sintering at 1600 °C

Effects of Ti(C, N) addition on the microstructure and mechanical properties of spark plasma sintered Si3N4/Ti(C, N) ceramic tool material

The spark plasma sintering of fine grained TiCN-Mo-Ni cermets