Abstract:The non-heat-treated, die-cast aluminum alloy samples were prepared meticulously via die-casting technology. The crystal structure, microstructure, and phase composition of the samples were comprehensively studied through electron backscatter diffraction (EBSD), metallographic microscopy, spectrometer, and transmission electron microscopy (TEM). The microhardness and tensile properties of the samples were tested. The die-cast samples were found to have desirable properties by studying the structure and performance of the samples. There were no defects, such as pores, cold partitions, or surface cracks, found. The metallographic structure of the samples was mainly α-Al, and various phases were distributed at the grain boundaries. Before heat treating, α-Al grains were mainly equiaxed with a great number of second phase particles at the grain boundaries. After heat treating, the α-Al grains were massive and coarsened, and the second phase grains were refined and uniformly distributed, compared with those before the heat treating. The EBSD results showed that the grain boundary Si particles were solid solution decomposed after heat treatment. The particles became smaller, and their distribution was more uniform. Transmission electron microscopy found that there were nano-scale Al-Mn, Al-Cu, and Cu phases dispersed in the samples. The average microhardness of the samples before heat treating was 114 HV0.1, while, after the heat treating, the microhardness reached 121 HV0.1. The mechanical features of the samples were tremendous, and the obtained die-cast aluminum alloy had non-heat-treatment performance, which was greater than the ordinary die-cast aluminum alloys with a similar composition. The tensile strength of the aluminum alloys reached up to 310 MPa before heat treatment.

Microstructure and Tribological Property Correlations of Die Cast and Spray Formed Al-30 wt.% Si Alloy

Influence of Rheo-Diecasting Processing Parameters on Microstructure and Mechanical Properties of Hypereutectic Al–30%Si Alloy

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Comparative analysis on high temperature tribological behaviour of additive manufactured and cast AlSi10Mg alloy

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

Microstructures and Wear Resistance of Al-25 wt.%Si Coatings Prepared by High-Efficiency Supersonic Plasma Spraying

A Comparative Study on Microstructure, Mechanical Property and Damping Capacity of Hypoeutectic Al–Si–Cu Alloy for Different Casting Technologies

Effect of Si on Phase Equilibria, Mechanical Properties and Tribological Behaviour of Al-Cu Alloy

The microstructures and properties of an al- 12 wt pct

A Comparative Study on Microstructure, Mechanical Property, and Electrical Conductivity of Al-7Si-0.6Mg Alloy Produced by High Pressure Die Casting and Semisolid Die Casting

A Comparison of the Sliding Wear Behavior of a Hypereutectic Al–Si Alloy Prepared by Spray-Deposition and Conventional Casting Methods

Microstructure and Properties of Semi-solid Die Casting of High Silicon Aluminum Alloy with High Thermal Conductivity

Effect of Fe and Mn additions on microstructure and wear properties of spray-deposited Al–20Si alloy

Mechanical and tribological properties of hybrid and monolithic reinforced hypoeutectic Al‐Si matrix composites

Microstructure and Mechanical Properties of Al-Si Alloys Produced by Rapid Solidification and Hot Extrusion

Microstructure and Mechanical Properties of Hypereutectic Al-High Si Alloys up to 70 wt.% Si-Content Produced from Pre-Alloyed and Blended Powder via Laser Powder Bed Fusion

A Study on High Strength, High Plasticity, Non-Heat Treated Die-Cast Aluminum Alloy

The characterization of Fe-rich phases in a high-pressure die cast hypoeutectic aluminum-silicon alloy

Towards high performance Al–Si–Fe alloy castings via rheo-diecasting: Effect of injection velocity and heat treatment on microstructure evolution and property

Microstructure and Mechanical Behavior of Multidirectional Forge SIMA Process Al- Si Hypereutectic Alloy

Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology