Abstract:Selective laser melting (SLM) of the 7xxx series Al alloy (Al-Zn-Mg-Cu) faces more challenge than other series aluminum alloy such as Al-Si system because of the high hot-cracking sensitivity. The porosity development and crack behavior of Al-Zn-Mg-Cu alloys fabricated at various scanning speeds in SLM process, as well as the influence of molten pool geometry were systematically investigated in this paper. Results show that the relative density over 99% can be achieved when the applied scanning speed is 150 mm/s. However, cracks are observed in almost all the as-deposited samples. The morphology, distribution and density of cracks were varied with the different molten pool geometry and scanning speed. Introduction 7xxx series Al alloys are characterized by high tensile strength (over 500Mpa), high corrosion resistance and good fatigue properties [1-2]. These characteristics make over 85% of the 7xxx series Al alloys to use in automotive and aerospace fields. With the development of automotive and aerospace fields, the need for integral component of 7xxx series Al alloys is increased. The convention processing techniques encounter many difficulties due to the complexity and thin-wall structure of integral component. Hence, new manufacturing process like SLM is inevitable to enhance the process. SLM is an addictive manufacturing process with a high potential for producing complexly shaped components [3-4]. Because of the high thermal conductivity, poor fluidity and easy oxidized of aluminum alloy, up to now, only casting AlSi10Mg [5-8] and Al-12Si [9-11] have been widely manufacturing by SLM due to the weld ability and flow behavior. Few works have been focus on other aluminum alloys [12] especially the 7xxx series Al alloy. So far, Kaufmauu et al. [13] fabricated EN AW 7050 alloy sample with a relative density over 99%. However, all samples exhibited cracks. Sistiaga et al. [14] obtained crack free Al7075 alloy samples by adding 4% silicon in SLM process. Wang et al. [15] reported that an Al-Zn-Mg-Cu alloy with high zinc was successfully produced by SLM. The hardness of the synthesized SLM samples was higher than the corresponding T6 cast samples after heat treatment. The present work investigated the feasibility for fabricated full dense Al7050 alloy. The morphology, distribution and density of cracks were also discussed under different scanning speed and molten pool geometry.

Study on the laser selective melting and forming process and organizational properties of a TiSi 2 -modified 7075 aluminum alloy

Si-Assisted Solidification Path and Microstructure Control of 7075 Aluminum Alloy with Improved Mechanical Properties by Selective Laser Melting

Selective laser melting of novel 7075 aluminum powders with internally dispersed TiC nanoparticles

Selective laser melting of 7075 aluminum alloy inoculated by Al–Ti–B: Grain refinement and superior mechanical properties

A novel strategy to additively manufacture 7075 aluminium alloy with selective laser melting

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Numerical simulation and experimental study of the 7075 aluminum alloy during selective laser melting

Selective laser melting additive manufacturing of 7xxx series Al-Zn-Mg-Cu alloy: Cracking elimination by co-incorporation of Si and TiB2

The crack and pore formation mechanism of Ti–47Al–2Cr–2Nb alloy fabricated by selective laser melting

POROSITY DEVELOPMENT AND CRACKING BEHAVIOR OF Al-Zn-Mg-Cu ALLOYS FABRICATED BY SELECTIVE LASER MELTING

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

A novel crack-free Ti-modified Al-Cu-Mg alloy designed for selective laser melting

Microstructure and Mechanical Property of Ti–5Al–5Mo–5V–3Cr–1Zr Alloy Fabricated by Selective Laser Melting with a Preheated Substrate

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Microstructures and tensile properties of a selective laser melted Al–Zn–Mg–Cu (Al7075) alloy by Si and Zr microalloying

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Tensile Behavior of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting: Effects of Microstructures and As-Built Surface Quality

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

A novel hierarchical manufacturing method of the selective laser melted Al 7075 alloy

Processing and characterization of crack-free 7075 aluminum alloys with elemental Zr modification by laser powder bed fusion