Abstract:Selective laser melting (SLM) of the 7xxx series Al alloy (Al-Zn-Mg-Cu) faces more challenge than other series aluminum alloy such as Al-Si system because of the high hot-cracking sensitivity. The porosity development and crack behavior of Al-Zn-Mg-Cu alloys fabricated at various scanning speeds in SLM process, as well as the influence of molten pool geometry were systematically investigated in this paper. Results show that the relative density over 99% can be achieved when the applied scanning speed is 150 mm/s. However, cracks are observed in almost all the as-deposited samples. The morphology, distribution and density of cracks were varied with the different molten pool geometry and scanning speed. Introduction 7xxx series Al alloys are characterized by high tensile strength (over 500Mpa), high corrosion resistance and good fatigue properties [1-2]. These characteristics make over 85% of the 7xxx series Al alloys to use in automotive and aerospace fields. With the development of automotive and aerospace fields, the need for integral component of 7xxx series Al alloys is increased. The convention processing techniques encounter many difficulties due to the complexity and thin-wall structure of integral component. Hence, new manufacturing process like SLM is inevitable to enhance the process. SLM is an addictive manufacturing process with a high potential for producing complexly shaped components [3-4]. Because of the high thermal conductivity, poor fluidity and easy oxidized of aluminum alloy, up to now, only casting AlSi10Mg [5-8] and Al-12Si [9-11] have been widely manufacturing by SLM due to the weld ability and flow behavior. Few works have been focus on other aluminum alloys [12] especially the 7xxx series Al alloy. So far, Kaufmauu et al. [13] fabricated EN AW 7050 alloy sample with a relative density over 99%. However, all samples exhibited cracks. Sistiaga et al. [14] obtained crack free Al7075 alloy samples by adding 4% silicon in SLM process. Wang et al. [15] reported that an Al-Zn-Mg-Cu alloy with high zinc was successfully produced by SLM. The hardness of the synthesized SLM samples was higher than the corresponding T6 cast samples after heat treatment. The present work investigated the feasibility for fabricated full dense Al7050 alloy. The morphology, distribution and density of cracks were also discussed under different scanning speed and molten pool geometry.

POROSITY DEVELOPMENT AND CRACKING BEHAVIOR OF Al-Zn-Mg-Cu ALLOYS FABRICATED BY SELECTIVE LASER MELTING

Selective laser melting additive manufacturing of 7xxx series Al-Zn-Mg-Cu alloy: Cracking elimination by co-incorporation of Si and TiB2

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Microstructures and tensile properties of a selective laser melted Al–Zn–Mg–Cu (Al7075) alloy by Si and Zr microalloying

Si-Assisted Solidification Path and Microstructure Control of 7075 Aluminum Alloy with Improved Mechanical Properties by Selective Laser Melting

Processing and characterization of crack-free 7075 aluminum alloys with elemental Zr modification by laser powder bed fusion

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Superior mechanical properties of a selective-laser-melted AlZnMgCuScZr alloy enabled by a tunable hierarchical microstructure and dual-nanoprecipitation

Cracking criterion for high strength Al–Cu alloys fabricated by selective laser melting

Study on the laser selective melting and forming process and organizational properties of a TiSi 2 -modified 7075 aluminum alloy

Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms

Role of defects on the high cycle fatigue behavior of selective laser melted Al–Mg–Sc–Zr alloy

The crack and pore formation mechanism of Ti–47Al–2Cr–2Nb alloy fabricated by selective laser melting

A novel strategy to additively manufacture 7075 aluminium alloy with selective laser melting

A novel hierarchical manufacturing method of the selective laser melted Al 7075 alloy

Process-Dependent Composition, Microstructure, and Printability of Al-Zn-Mg and Al-Zn-Mg-Sc-Zr Alloys Manufactured by Laser Powder Bed Fusion

A study of selective laser melting process for pure zinc and Zn10mg alloy on process parameters and mechanical properties

A novel crack-free Ti-modified Al-Cu-Mg alloy designed for selective laser melting

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties