Abstract:Selective laser melting (SLM) of the 7xxx series Al alloy (Al-Zn-Mg-Cu) faces more challenge than other series aluminum alloy such as Al-Si system because of the high hot-cracking sensitivity. The porosity development and crack behavior of Al-Zn-Mg-Cu alloys fabricated at various scanning speeds in SLM process, as well as the influence of molten pool geometry were systematically investigated in this paper. Results show that the relative density over 99% can be achieved when the applied scanning speed is 150 mm/s. However, cracks are observed in almost all the as-deposited samples. The morphology, distribution and density of cracks were varied with the different molten pool geometry and scanning speed. Introduction 7xxx series Al alloys are characterized by high tensile strength (over 500Mpa), high corrosion resistance and good fatigue properties [1-2]. These characteristics make over 85% of the 7xxx series Al alloys to use in automotive and aerospace fields. With the development of automotive and aerospace fields, the need for integral component of 7xxx series Al alloys is increased. The convention processing techniques encounter many difficulties due to the complexity and thin-wall structure of integral component. Hence, new manufacturing process like SLM is inevitable to enhance the process. SLM is an addictive manufacturing process with a high potential for producing complexly shaped components [3-4]. Because of the high thermal conductivity, poor fluidity and easy oxidized of aluminum alloy, up to now, only casting AlSi10Mg [5-8] and Al-12Si [9-11] have been widely manufacturing by SLM due to the weld ability and flow behavior. Few works have been focus on other aluminum alloys [12] especially the 7xxx series Al alloy. So far, Kaufmauu et al. [13] fabricated EN AW 7050 alloy sample with a relative density over 99%. However, all samples exhibited cracks. Sistiaga et al. [14] obtained crack free Al7075 alloy samples by adding 4% silicon in SLM process. Wang et al. [15] reported that an Al-Zn-Mg-Cu alloy with high zinc was successfully produced by SLM. The hardness of the synthesized SLM samples was higher than the corresponding T6 cast samples after heat treatment. The present work investigated the feasibility for fabricated full dense Al7050 alloy. The morphology, distribution and density of cracks were also discussed under different scanning speed and molten pool geometry.

Processing and characterization of crack-free 7075 aluminum alloys with elemental Zr modification by laser powder bed fusion

Facile and cost-effective approach to additively manufacture crack-free 7075 aluminum alloy by laser powder bed fusion

Microstructure, mechanical properties, and crack formation of aluminum alloy 6063 produced via laser powder bed fusion

Characterization of crack-free AA-7075 fabricated by laser powder bed fusion with addition of Zr50.7Cu28Al12.3Ni9 metallic glass

Crack initiation mechanism of laser powder bed fusion additive manufactured Al-Zn-Mg-Cu alloy

Laser powder bed fusion of Zr-modified Al–Cu–Mg alloy: Crack-inhibiting, grain refinement, and mechanical properties

Process-Dependent Composition, Microstructure, and Printability of Al-Zn-Mg and Al-Zn-Mg-Sc-Zr Alloys Manufactured by Laser Powder Bed Fusion

Effect of Powder Spreading Parameters on Laser Absorption Behavior and Processability of High‐Strength Aluminum Alloy Fabricated by Laser Powder Bed Fusion

Microstructure and Mechanical Properties of a Novel Sc and Zr Modified 7075 Aluminum Alloy Prepared by Selective Laser Melting

Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF

Effect of 0.5 wt% Zr on defects, microstructure and mechanical properties of Al-3.6Zn-0.6Mg alloy fabricated by laser powder bed fusion

Tailored porosity in additive manufacturing of 7075 aluminum alloy for crack suppression and high strength

Exploiting the rapid solidification potential of laser powder bed fusion in high strength and crack-free Al-Cu-Mg-Mn-Zr alloys

Effective Control of Microstructure Evolution in AZ91D Magnesium Alloy by SiC Nanoparticles in Laser Powder-Bed Fusion

Requirements for Processing High-Strength AlZnMgCu Alloys with PBF-LB/M to Achieve Crack-Free and Dense Parts

Microstructure characterization and mechanical properties of crack-free Al-Cu-Mg-Y alloy fabricated by laser powder bed fusion

POROSITY DEVELOPMENT AND CRACKING BEHAVIOR OF Al-Zn-Mg-Cu ALLOYS FABRICATED BY SELECTIVE LASER MELTING

Fabrication of crack-free aluminum alloy 6061 parts using laser foil printing process

Cracking mechanism and its susceptibility to scanning speed during laser power bed fusion processed high-strength 2024Al alloy

Microstructural Evolution of a High-Strength Zr-Ti-Modified 2139 Aluminum Alloy for Laser Powder Bed Fusion

Role of Er on the Densification, Microstructure and Mechanical Properties of 7075 Aluminium Alloys Manufactured by Laser Powder Bed Fusion