Abstract:Selective laser melting (SLM) of the 7xxx series Al alloy (Al-Zn-Mg-Cu) faces more challenge than other series aluminum alloy such as Al-Si system because of the high hot-cracking sensitivity. The porosity development and crack behavior of Al-Zn-Mg-Cu alloys fabricated at various scanning speeds in SLM process, as well as the influence of molten pool geometry were systematically investigated in this paper. Results show that the relative density over 99% can be achieved when the applied scanning speed is 150 mm/s. However, cracks are observed in almost all the as-deposited samples. The morphology, distribution and density of cracks were varied with the different molten pool geometry and scanning speed. Introduction 7xxx series Al alloys are characterized by high tensile strength (over 500Mpa), high corrosion resistance and good fatigue properties [1-2]. These characteristics make over 85% of the 7xxx series Al alloys to use in automotive and aerospace fields. With the development of automotive and aerospace fields, the need for integral component of 7xxx series Al alloys is increased. The convention processing techniques encounter many difficulties due to the complexity and thin-wall structure of integral component. Hence, new manufacturing process like SLM is inevitable to enhance the process. SLM is an addictive manufacturing process with a high potential for producing complexly shaped components [3-4]. Because of the high thermal conductivity, poor fluidity and easy oxidized of aluminum alloy, up to now, only casting AlSi10Mg [5-8] and Al-12Si [9-11] have been widely manufacturing by SLM due to the weld ability and flow behavior. Few works have been focus on other aluminum alloys [12] especially the 7xxx series Al alloy. So far, Kaufmauu et al. [13] fabricated EN AW 7050 alloy sample with a relative density over 99%. However, all samples exhibited cracks. Sistiaga et al. [14] obtained crack free Al7075 alloy samples by adding 4% silicon in SLM process. Wang et al. [15] reported that an Al-Zn-Mg-Cu alloy with high zinc was successfully produced by SLM. The hardness of the synthesized SLM samples was higher than the corresponding T6 cast samples after heat treatment. The present work investigated the feasibility for fabricated full dense Al7050 alloy. The morphology, distribution and density of cracks were also discussed under different scanning speed and molten pool geometry.

Tailored porosity in additive manufacturing of 7075 aluminum alloy for crack suppression and high strength

Facile and cost-effective approach to additively manufacture crack-free 7075 aluminum alloy by laser powder bed fusion

Processing and characterization of crack-free 7075 aluminum alloys with elemental Zr modification by laser powder bed fusion

Microstructure, mechanical properties, and crack formation of aluminum alloy 6063 produced via laser powder bed fusion

Fabrication of crack-free aluminum alloy 6061 parts using laser foil printing process

Revealing mechanism of pore defect formation in laser directed energy deposition of aluminum alloy via in-situ synchrotron X-ray imaging

Laser powder bed fusion of crack-free TiN/Al7075 composites with enhanced mechanical properties

Cracking in Laser Additively Manufactured W: Initiation Mechanism and a Suppression Approach by Alloying

A novel strategy to additively manufacture 7075 aluminium alloy with selective laser melting

POROSITY DEVELOPMENT AND CRACKING BEHAVIOR OF Al-Zn-Mg-Cu ALLOYS FABRICATED BY SELECTIVE LASER MELTING

Microstructure characterization and mechanical properties of crack-free Al-Cu-Mg-Y alloy fabricated by laser powder bed fusion

The crack and pore formation mechanism of Ti–47Al–2Cr–2Nb alloy fabricated by selective laser melting

Requirements for Processing High-Strength AlZnMgCu Alloys with PBF-LB/M to Achieve Crack-Free and Dense Parts

Crack Formation and Control in an AlCoCrFeNi High Entropy Alloy Fabricated by Selective Laser Melting

Review on Laser Directed Energy Deposited Aluminum Alloys

Si-Assisted Solidification Path and Microstructure Control of 7075 Aluminum Alloy with Improved Mechanical Properties by Selective Laser Melting

Cracking susceptibility control of 7075 aluminum alloy in pulsed laser welding with filler strip

Crack Control in Additive Manufacturing by Leveraging Process Parameters and Lattice Design

Computational design of a crack-free aluminum alloy for additive manufacturing

Cracking mechanism and its susceptibility to scanning speed during laser power bed fusion processed high-strength 2024Al alloy

Laser Additive Manufacturing of High-Strength Aluminum Alloys: Challenges and Strategies