Abstract:With the growing demand for lightweight and high-performance components applied in extreme aerospace environments, there is a prospective interest in producing the integrated multi-material components consisting of titanium alloy and aluminum alloy. Laser powder bed fusion (LPBF), as a laser powder bed based additive manufacturing process with a high production flexibility, shows a promising potential in creating multi-material components. However, due to the possibility of the generation of various intermetallic compounds (IMCs) at the interface, it has been a significant challenge to fabricate reliable Ti/Al alloy multi-material components without any crack formation by LPBF. In this study, the Ti6Al4V/AlMgScZr multi-material parts were fabricated by LPBF and the effects of building parameters of AlMgScZr on the residual stress and crack control of Ti6Al4V/AlMgScZr multi-material parts were investigated. The evolution mechanisms of IMC phases at the interface under laser interaction were further revealed. Due to the change of elemental compositions and difference in Gibbs free energies of IMCs, a gradient ordered transition zone with a width of about 450 μm consisting of Al 3 Ti, TiAl, and Ti 3 Al was formed from AlMgScZr to Ti6Al4V. A finite element model was established to explain the effects of process parameters on residual stress evolution, cracking formation and its control. As the scan speed increased from 500 to 1100 mm/s and the attendant building height of AlMgScZr increased to 60 layers, the residual stress of laser processed Ti6Al4V decreased from 439 to 364 MPa, but the residual stress of AlMgScZr increased from 195 to 303 MPa. As the applied scan speed was enhanced to process AlMgScZr, the element diffusion was mitigated, thereby reducing the formation of IMCs and stress concentration. This study shows the possibility of in-situ control of IMCs and residual stress by process optimization during LPBF preparation of titanium alloy/aluminum multi-material parts without crack formation.

Cracking mechanism and its susceptibility to scanning speed during laser power bed fusion processed high-strength 2024Al alloy

Circumventing Solidification Cracking Susceptibility in Al–Cu Alloys Prepared by Laser Powder Bed Fusion

Laser powder bed fusion of Zr-modified Al–Cu–Mg alloy: Crack-inhibiting, grain refinement, and mechanical properties

Spreading Behavior and Hot Cracking Mechanism of Single Tracks in High Strength Al–Cu–Mg–Mn Alloy Fabricated by Laser Powder Bed Fusion

Processing defect, microstructure evolution and mechanical properties of laser powder bed fusion Al-12Si alloys

Influence of Laser-Based Powder Bed Fusion of Metals Process Parameters on the Formation of Defects in Al-Zn-Mg-Cu Alloy Using Path Analysis

Reducing cracking sensitivity of CM247LC processed via laser powder bed fusion through composition modification

Effect of Powder Spreading Parameters on Laser Absorption Behavior and Processability of High‐Strength Aluminum Alloy Fabricated by Laser Powder Bed Fusion

Microstructure, mechanical properties, and crack formation of aluminum alloy 6063 produced via laser powder bed fusion

Processing and characterization of crack-free 7075 aluminum alloys with elemental Zr modification by laser powder bed fusion

Temperature gradient induced tough-brittle transition behavior of a high-strength Al-4.2Mg-0.4Sc-0.2Zr alloy fabricated by laser powder bed fusion additive manufacturing

The Effect of Thermal Cycle on Hot Cracking Evolution and Formation Mechanism in Thin Wall, Single Layer, and Cubic Samples of High-Strength Al-Cu-Mg-Mn Alloys Fabricated by Laser Powder Bed Fusion

The influence of building parameters on residual stress, interfacial structure, and cracking control of laser powder bed fusion processed Ti6Al4V/AlMgScZr multi-material parts

Microstructure characterization and mechanical properties of crack-free Al-Cu-Mg-Y alloy fabricated by laser powder bed fusion

Effect of laser process parameters on thermal behavior and residual stress of high-strength aluminum alloy processed by laser powder bed fusion

Microstructure and Fatigue Behavior of High-Performance Aluminum Alloy Al2024 Produced by Laser Powder Bed Fusion

Microstructural Evaluation and Tensile Properties of Al-Mg-Sc-Zr Alloys Prepared by LPBF

Controlling crack formation and porosity in laser powder bed fusion: Alloy design and process optimisation

Requirements for Processing High-Strength AlZnMgCu Alloys with PBF-LB/M to Achieve Crack-Free and Dense Parts

Influence of Scanning Strategy and Post-Treatment on Cracks and Mechanical Properties of Selective-Laser-Melted K438 Superalloy

Simultaneous regulation of strength and ductility of laser powder bed fusion manufactured Haynes 230 alloy