Abstract:Due to a good combination of high hardness, wear resistance, toughness, resistance to high operating temperatures, and fairly low material cost, AISI H13 tool steel is commonly used in the manufacture of injection molds. Additive manufacturing (AM) such as selective laser melting (SLM), due to the layer-wise nature of the process, offers substantial geometric design freedom in comparison with conventional subtractive manufacturing methods, thereby enabling a construction of complex near-net shape parts with internal cavities like conformal cooling channels. The quality of SLM-manufactured parts mainly depends on the part geometry, build orientation and scanning strategy, and processing parameters. In this study, samples of H13 tool steel with a size of 10 × 10 × 15 mm3 were SLM-manufactured using a laser power of 100, 200, and 300 W; scanning speed of 200, 400, 600, 800, 1000, and 1200 mm/s; and hatch spacing of 80 and 120 µm. A constant layer thickness of 40 µm, 67° scanning rotation between subsequent layers, and a stripe scanning strategy were maintained during the process. The samples were built considering a preheating of 200 °C. The relative density, surface roughness, crack formation, microstructure, and hardness were evaluated. The relative density is shown to increase with increasing the volumetric energy density up to a value of about 60 J/mm3 and then no significant increase can be pointed out; the maximum relative density of 99.7% was obtained. A preheating of 200 °C generally aids to increase the relative density and eliminate the crack formation. The microstructure of built samples shows fine equiaxed cellular-dendritic structure with martensite and some retained austenite. The microhardness of the as-built samples was found to vary from 650 to 689 HV 0.2, which is comparable to a conventionally produced H13 tool steel.

High-speed manufacturing-driven strength-ductility improvement of H13 tool steel fabricated by selective laser melting

Simultaneous enhancements of strength and ductility of a selective laser melted H13 steel through inoculation treatment

Microstructures and Mechanical Properties of H13 Tool Steel Fabricated by Selective Laser Melting

Selective laser melting of H13: microstructure and residual stress

Process-Structure-Property Relationships of AISI H13 Tool Steel Processed with Selective Laser Melting

Effect of Heat Treatment on Microstructural Evolution, Mechanical Properties and Tribological Properties of H13 Steel Prepared Using Selective Laser Melting

Ultrastrong and Ductile Additively-Manufactured Medium-Carbon Steel Via Modulating Austenite Stability

Assessment of Mechanical Behavior in H13 Tool Steel Synthesized through Electron Beam Melting and Selective Laser Melting Techniques

SLM additive manufacture of H13 tool steel with conformal cooling and structural lattices

Additive Manufacturing of AISI H13 Tool Steel with Combinations of Higher Laser Power and Scan Speed: Microstructural and Mechanical Properties Insights

Microstructure evolution and mechanical properties of H13 steel produced by Selective Electron Beam Melting

Relative Density of Mold Steel H13 Fabricated by Hybrid Laser Spot Melting

Impact Testing of H13 Tool Steel Processed with Use of Selective Laser Melting Technology

Influence of Cell Structure on Yield Strength and Strain‐Hardening Behavior in Additively Manufactured H13 Hot Work Tool Steel

Achieving Excellent Strength and Ductility of 24crnimoy Alloy Steel Fabricated by High Power Selective Laser Melting Technology

A short review on selective laser melting of H13 steel

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Simultaneously enhanced strength and ductility for 3D-printed stainless steel 316L by selective laser melting

Fabrication and Characterization of AISI 420 Stainless Steel Using Selective Laser Melting

Microstructure, Properties and Crack Suppression Mechanism of High-speed Steel Fabricated by Selective Laser Melting at Different Process Parameters

Effects of laser scanning speed on the microstructure and mechanical properties of 2205 duplex stainless steel fabricated by selective laser melting