Abstract:In some traditional formative and additive manufacturing processes widely used in the fabrication of steel products, stress conditions and metallurgy typically result in a strong texture and mechanical anisotropy in both rolling high-strength low-alloy steel and additive manufacturing stainless steel products. To resolve this problem, we have investigated the effectiveness of a novel wire-arc additive manufacturing method in which the heat source is substituted by high-efficiency submerged arc plasma i.e., submerged arc additive manufacturing. An isotropic microstructure can be obtained in the bulk of large-scale low-carbon steel components by ensuring a complete columnar-to-equiaxed transition. We found that the top zone of the as-deposited component comprised columnar α-Fe grains with a typical preferential <001>α orientation. Multiple allotropic transformations were triggered by an in-situ intrinsic heat treatment (mainly the combination of multi-layer-penetration normalizing, full-layer-penetration inter-critical annealing, and long-duration tempering—i.e., NIT). Consequently, when the net bead height was no greater than the width of the fine grain zone affected by the previous layer of deposition, the microstructures in each new layer could be progressively refined and homogenized. Therefore, the intermediate zone was predominantly composed of fully equiaxed α-Fe and displayed homogeneous characteristics along the build direction. During full-layer NIT treatment, the pearlite was spheroidized slightly, reduced both in size (from 4μm to 2μm) and in area fraction (from ~5% to ~1%), thereby mitigating cracking susceptibility. Moreover, not only were the intracrystalline dislocations significantly reduced, but also their morphology evolved from tangled to movable lines. These changes, along with finer grains and the formation of high-angle grain boundaries, led to lower and more dispersed internal strain in the α-Fe matrix. Consequently, excellent Charpy toughness (over 300 J at -60 °C) with minimal deterioration in strength was achieved. Impact, tensile, and hardness tests revealed nearly isotropic mechanical characteristics. We believe that this novel method shows tremendous promise in large-scale additive manufacturing.

Ultrastrong and Ductile Additively-Manufactured Medium-Carbon Steel Via Modulating Austenite Stability

An ultra-high strength martensitic steel fabricated using selective laser melting additive manufacturing: Densification, microstructure, and mechanical properties

Simultaneous enhancements of strength and ductility of a selective laser melted H13 steel through inoculation treatment

Enhanced strength-ductility synergy of selective laser melted reduced activation ferritic/martensitic steel via heterogeneous microstructure modification

Microstructures and Mechanical Properties of H13 Tool Steel Fabricated by Selective Laser Melting

Microstructural Evolution of a FeCo15Cr14Ni4Mo3 Maraging Steel with High Ductility Prepared by Selective Laser Melting

Selective laser melting of H13: microstructure and residual stress

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Achieving Unexpected Strength and Ductility Synergies in Heterogeneous Metastable Lamellar Steels

Enhanced strength–ductility synergy and transformation-induced plasticity of the selective laser melting fabricated 304L stainless steel

Simultaneously enhanced strength and ductility for 3D-printed stainless steel 316L by selective laser melting

In-situ alloyed ultrahigh strength steels via additive manufacturing

Rationalization of brittleness and anisotropic mechanical properties of H13 steel fabricated by selective laser melting

Additively Manufactured Ultrastrong Al-containing Austenitic Stainless Steels Via Engineering Cellular Structure with Multi-Nanoprecipitates

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

Achieving Ultrahigh Yield Strength and Decent Toughness in an In-Situ Alloyed H13 Steel Via Laser Powder Bed Fusion

Submerged arc additive manufacturing (SAAM) of low-carbon steel: Effect of in-situ intrinsic heat treatment (IHT) on microstructure and mechanical properties

Plastically heterogeneity-driven fracture in additive manufactured steels

High-speed manufacturing-driven strength-ductility improvement of H13 tool steel fabricated by selective laser melting

Superior strength-ductility in laser aided additive manufactured high-strength steel by combination of intrinsic tempering and heat treatment

Enhancement of fatigue resistance of additively manufactured 304L SS by unique heterogeneous microstructure