Abstract:Due to a good combination of high hardness, wear resistance, toughness, resistance to high operating temperatures, and fairly low material cost, AISI H13 tool steel is commonly used in the manufacture of injection molds. Additive manufacturing (AM) such as selective laser melting (SLM), due to the layer-wise nature of the process, offers substantial geometric design freedom in comparison with conventional subtractive manufacturing methods, thereby enabling a construction of complex near-net shape parts with internal cavities like conformal cooling channels. The quality of SLM-manufactured parts mainly depends on the part geometry, build orientation and scanning strategy, and processing parameters. In this study, samples of H13 tool steel with a size of 10 × 10 × 15 mm3 were SLM-manufactured using a laser power of 100, 200, and 300 W; scanning speed of 200, 400, 600, 800, 1000, and 1200 mm/s; and hatch spacing of 80 and 120 µm. A constant layer thickness of 40 µm, 67° scanning rotation between subsequent layers, and a stripe scanning strategy were maintained during the process. The samples were built considering a preheating of 200 °C. The relative density, surface roughness, crack formation, microstructure, and hardness were evaluated. The relative density is shown to increase with increasing the volumetric energy density up to a value of about 60 J/mm3 and then no significant increase can be pointed out; the maximum relative density of 99.7% was obtained. A preheating of 200 °C generally aids to increase the relative density and eliminate the crack formation. The microstructure of built samples shows fine equiaxed cellular-dendritic structure with martensite and some retained austenite. The microhardness of the as-built samples was found to vary from 650 to 689 HV 0.2, which is comparable to a conventionally produced H13 tool steel.

Fabrication and Characterization of AISI 420 Stainless Steel Using Selective Laser Melting

Process-Structure-Property Relationships of AISI H13 Tool Steel Processed with Selective Laser Melting

In-situ generation of high-strength AISI 1045 steel with SiO 2 nano-precipitation by selective laser melting (SLM)

Effects of process parameters on the microstructure and mechanical properties of AISI 1045 steel prepared by selective laser melting

Microstructures and Mechanical Properties of H13 Tool Steel Fabricated by Selective Laser Melting

Microstructure and dynamic-mechanical property of a selective laser melting AISI 316 L stainless steel

Simultaneous enhancements of strength and ductility of a selective laser melted H13 steel through inoculation treatment

High-Strength 430 ferritic stainless steel fabricated by selective laser melting process

Selective laser melting of H13: microstructure and residual stress

Selective Laser Melting and Mechanical Properties of Stainless Steels

Study on performance optimization of 316L stainless steel parts by High-Efficiency Selective Laser Melting

Effect of selective laser melting process parameters on the microstructure and properties of a precipitation hardening stainless steel

Tensile Properties of Selective Laser Melted 316L Stainless Steel

Investigation of Selective Laser Melting of 2205 steel precipitates and heat treatment improvement

Microstructure and Mechanical Properties of 18Ni-300 Maraging Steel Fabricated by Selective Laser Melting

The investigation of microstructure and mechanical properties of tool steel produced by selective laser melting technology

The mechanical properties and corrosion resistance of selective laser melting 30CrMnSiA steel

Selective laser melting of maraging steel: mechanical properties development and its application in mold

On the Anisotropic Mechanical Properties of Selective Laser-Melted Stainless Steel

Selective Laser Melting of Duplex Stainless Steel 2205: Effect of Post-Processing Heat Treatment on Microstructure, Mechanical Properties, and Corrosion Resistance

Microstructural Evolution of a FeCo15Cr14Ni4Mo3 Maraging Steel with High Ductility Prepared by Selective Laser Melting