Abstract:In order to fabricate large-area PVSCs, one of the critical challenges is to understand the infl uence of ambient environment on resultant perovskite thin-fi lms since perovskite crystals are sensitive to humidity under ambient condition. It has been shown that perovskite crystals degrade gradually when they are in contact with ambient moisture for certain time. [ 31,32 ] Therefore, most of the high performance perovskite solar cells are prepared in glovebox to avoid contacting moisture. However, fabricating PVSCs under ambient condition is inevitable if we desire to transition from laboratory research into large-scale applications. Lately, there are several encouraging reports about allowing limited amount of moisture to facilitate the perovskite crystallization and improve the performance of resulting device. [ 33,34 ] However, there are no detailed underlying mechanisms explained on how moisture affects perovskite crystallization so far. To alleviate these problems, we have investigated the feasibility of achieving fully printable PVSCs by the blade-coating technique under the ambient condition. The blade-coating fabrication has been widely used to fabricate OSCs and is proven to be a simple, environment-friendly, and low-cost method for the solution-processed photovoltaic. Compared to the screen printing, it not only can print nanoparticles, but also can print all kinds of solutions with any concentration. Moreover, the fi lm morphology control of the blade-coating method is much better than the spray coating and roll-to-roll printing; high-quality photoactive layers with controllable thickness can be accomplished by using a precisely translational blade under the ambient condition with controlled relative humidity. The PVSCs with a confi guration of ITO/poly(3,4-ethylenedioxy-thiophene):poly(4-styrenesulfonate) (PEDOT:PSS)/ CH 3 NH 3 PbI X Cl 3− X /[6,6]-phenyl-C 61 butyric acid methyl ester (PC 61 BM)/Bis-C 60 /Ag were fabricated to realize the fully printable process, as illustrated in Figure 1 a. All constituent interlayers, except for the Ag top electrode, were prepared via blade-coating. The coating conditions were optimized to allow the preparation of high-quality interlayer fi lms. Especially, the effect of humidity was carefully investigated and monitored to facilitate the crystallization of perovskite fi lms under ambient condition. Finally, high PCE (10.44% ± 0.23%) device could be achieved after optimizing the blade-coating process and relative humidity in environment. Moreover, a high-performance fl exible PVSC with a PCE of 7.14% ± 0.31% was demonstrated for the fi rst time using this low-temperature (<150 °C) fully printable process. The exceptional photovoltaic properties demonstrated recently for organic–inorganic halide perovskites (such as CH 3 NH 3 PbX 3 (X = Cl, Br, or I)) have attracted great attention from researchers. [ 1–8 ] The promising features of these perovskites include broad and intense absorption spectra, [ 9 ] appropriate semiconducting properties, [ 10 ] long carrier diffusion length, [ 11,12 ]

Fully Printed HTL-Free MAPbI3 Perovskite Solar Cells with Carbon Electrodes

Methylamine-Based Method to Deposit MAPbI3 Nanoscale-Thick Films for Efficient Perovskite Solar Cells with Carbon Electrodes

Fully Screen‐Printed Perovskite Solar Cells with 17% Efficiency via Tailoring Confined Perovskite Crystallization within Mesoporous Layer

Reproducible One-Step Fabrication of Compact MAPbl(3-x)Cl(x) Thin Films Derived from Mixed-Lead-Halide Precursors

Organic Bromide Salts Interface Modification for High-Efficiency Perovskite Solar Cells with Printed Carbon Electrode

Cost effective perovskite solar cells with a high efficiency and open-circuit voltage based on a perovskite-friendly carbon electrode

Room‐Temperature‐Processed, Carbon‐Based Fully Printed Mesoscopic Perovskite Solar Cells with 15% Efficiency

Semitransparent CH3NH3PbI3 Films Achieved by Solvent Engineering for Annealing‐ and Electron Transport Layer‐Free Planar Perovskite Solar Cells

Efficient, stable, and fully printed carbon-electrode perovskite solar cells enabled by hole-transporting bilayers

Low Temperature Processed Fully Printed Efficient Planar Structure Carbon Electrode Perovskite Solar Cells and Modules

Constructing 2D passivation layer on perovskites based on 3-chlorobenzylamine enables efficient and stable perovskite solar cells

MAPbI3-xBrx mixed halide perovskites for fully printable mesoscopic solar cells with enhanced efficiency and less hysteresis.

Fully Printed High‐Performance Quasi‐Two‐Dimensional Perovskite Solar Cells via Multifunctional Interfacial Engineering

High‐Performance Fully Printable Perovskite Solar Cells via Blade‐Coating Technique under the Ambient Condition

Constructing Additives Synergy Strategy to Doctor-Blade Efficient CH3 NH3 PbI3 Perovskite Solar Cells under a Wide Range of Humidity from 45% to 82.

In-Situ Growth of Perovskite Stacking Layer for High-Efficiency Carbon-Based Hole Conductor Free Perovskite Solar Cells

A Modified Sequential Deposition Route for High-Performance Carbon-Based Perovskite Solar Cells under Atmosphere Condition

Efficient and Stable Large Bandgap MAPbBr<sub>3</sub> Perovskite Solar Cell Attaining an Open Circuit Voltage of 1.65 V

Constructing Additives Synergy Strategy to Doctor‐Blade Efficient CH3NH3PbI3 Perovskite Solar Cells under a Wide Range of Humidity from 45% to 82%

Single-step Chemical Vapor Deposition of Methyl Ammonium Lead Halide Perovskite for p-i-n Solar Cells

Perovskite hetero-bilayer for efficient charge-transport-layer-free solar cells