Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

In-Situ Growth of Perovskite Stacking Layer for High-Efficiency Carbon-Based Hole Conductor Free Perovskite Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

In Situ Reconstruction Post‐Treatment for Efficient Carbon‐Based Hole‐Conductor‐Free Printable Mesoscopic Perovskite Solar Cells

Ligand‐Induced In Situ Epitaxial Growth of PbI2 Nanosheets/MAPbI3 Heterojunction Realizes High‐Performance HTM‐Free Carbon‐Based MAPbI3 Solar Cells

Regulating molecular stacking to construct a superior interfacial contact for highly efficient and stable perovskite solar cells

Contact Engineering and In‐Situ Formation of 2D Perovskite via Solid‐Phase Growth for Efficient Hole‐Transport‐Layer‐Free Perovskite Solar Cells

Greatly enhanced power conversion efficiency of hole-transport-layer-free perovskite solar cell via coherent interfaces of perovskite and carbon layers

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

A 2D/3D heterojunction engineering for carbon-based hole-transport-layer-free perovskite solar cells

Cross-stacked superaligned carbon nanotube electrodes for efficient hole conductor-free perovskite solar cells

A Highly Stable Hole-Conductor-free CsxMA1-xPbI3 Perovskite Solar Cell Based on Carbon Counter Electrode

Back interface management by multifunctional composite carbon nanospheres electrode for efficient and stable HTL-free carbon-based perovskite solar cells

2D PEA 2 PbI 4 –3D MAPbI 3 Composite Perovskite Interfacial Layer for Highly Efficient and Stable Mixed-Ion Perovskite Solar Cells

High-performance Carbon Electrode-Based CsPbI2Br Inorganic Perovskite Solar Cell Based on Poly(3-Hexylthiophene)-carbon Nanotubes Composite Hole-Transporting Layer.

Porous Organic Cage Induced Spontaneous Restructuring of Buried Interface Toward High‐Performance Perovskite Photovoltaic

Simultaneous Interface Amelioration and Energy Level Modulation Using In Situ Polymerized Molecules for Efficient and Stable Perovskite Solar Cells

Efficient and Stable Perovskite Solar Cells by B-Site Compositional Engineered All-Inorganic Perovskites and Interface Passivation

Charge extraction via graded doping of hole transport layers gives highly luminescent and stable metal halide perovskite devices

Multistrategy Toward Highly Efficient and Stable CsPbI 2 Br Perovskite Solar Cells Based on Dopant‐Free Poly(3‐Hexylthiophene)

Building Bulk Heterojunction to Enhance Hole Extraction for High‐Performance Printable Carbon‐Based Perovskite Solar Cells

Interface Modification Via a Hydrophobic Polymer Interlayer for Highly Efficient and Stable Carbon-Based Inorganic Perovskite Solar Cells