Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Interface Modification Via a Hydrophobic Polymer Interlayer for Highly Efficient and Stable Carbon-Based Inorganic Perovskite Solar Cells

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Improving Photovoltaic Performance of Carbon-Based CsPbBr3 Perovskite Solar Cells by Interfacial Engineering Using P3HT Interlayer

Multifunctional Interface Modification Enables Efficient and Stable HTL-Free Carbon-Electroded CsPbI2Br Perovskite Solar Cells

High-performance Carbon Electrode-Based CsPbI2Br Inorganic Perovskite Solar Cell Based on Poly(3-Hexylthiophene)-carbon Nanotubes Composite Hole-Transporting Layer.

A double perovskite participation for promoting stability and performance of Carbon-Based CsPbI2Br perovskite solar cells

Improving efficiency of polymer hole transport layer based perovskite solar cells via interfacial modification

A multifunctional interlayer for highly stable and efficient perovskite solar cells based on pristine poly(3- hexylthiophene)

Interlayer Modification Using Phenylethylamine Tetrafluoroborate for Highly Effective Perovskite Solar Cells

High-performance carbon-based CsPbI2Br perovskite solar cells via small molecule modification

Improving Efficiency and Stability of Perovskite Solar Cells Enabled by A Near-Infrared-Absorbing Moisture Barrier

Ester‐Functionalized Polythiophene Interlayers for Enhanced Performance and Stability of Perovskite Solar Cells

Polyethyleneimine-functionalized carbon nanotubes as an interlayer to bridge perovskite/carbon for all inorganic carbon-based perovskite solar cells

Surface Passivation of CsPbI 3 Films for Efficient and Stable Hole-Transporting Layer-Free Carbon-Based Perovskite Solar Cells

Modification of perovskite/HTL interface with cooperative polymers bilayer (PTB7-Th/P3HT) to improve perovskite solar cell efficiency and stability

Bridging the Interfacial Contact for Improved Stability and Efficiency of Inverted Perovskite Solar Cells

Boosting the performance of low-temperature processed CsPbI2Br planar perovskite solar cells by interface engineering

Improvement of Thermal Stability and Photoelectric Performance of Cs2PbI2Cl2/CsPbI2.5Br0.5 Perovskite Solar Cells by Triple-Layer Inorganic Hole Transport Materials

An Interface Co-modification Strategy for Improving the Efficiency and Stability of CsPbI 3 Perovskite Solar Cells

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Efficient and Stable Carbon‐Based CsPbIBr 2 Perovskite Solar Cells by 4‐Aminomethyltetrahydropyran Acetate Modification