Abstract:Carbon-based perovskite solar cells without a hole transport layer (HTL) are considered to be highly stable and of low cost. However, the deficient interface contact and inferior hole extraction capability restrict the further improvement of the device efficiency. Introducing a hole transporting layer, such as cuprous thiocyanate (CuSCN), can enhance the hole extraction ability and improve the interface contact. However, our further studies indicated that—at a certain temperature—for carbon-based solar cells, in the CuSCN layer, the diffusion of SCN– into the perovskite film would produce more interfacial defects and aggravate nonradiative recombination, thus hindering the carrier transport. We further disclosed the reasons for performance attenuation during the thermal treatment of carbon electrodes, proposed a vacuum-assisted drying process for carbon electrodes to suppress the destructive effect, and finally, achieved an enhanced efficiency for perovskite solar cells with a CuSCN inorganic HTL and screen-printable carbon electrode. Also, the unencapsulated perovskite solar cell demonstrated over 80% efficiency retention after being stored in an ambient atmosphere (45–70% relative humidity (RH)) for over 1000 h and maintained over 85% efficiency retention for 309 h of 1-sun irradiation under a continuous nitrogen flow under open-circuit conditions.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c05495?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c05495</a>.Material characterization (UV–vis, SEM, XRD, EIS); resistance of the carbon electrodes; parameters from the fitting of the TRPL results; and photovoltaic properties of the devices (J–V curves and J–V metrics) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c05495/suppl_file/am1c05495_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Employing 2D‐Perovskite as an Electron Blocking Layer in Highly Efficient (18.5%) Perovskite Solar Cells with Printable Low Temperature Carbon Electrode

Contact Engineering and In‐Situ Formation of 2D Perovskite via Solid‐Phase Growth for Efficient Hole‐Transport‐Layer‐Free Perovskite Solar Cells

A 2D/3D heterojunction engineering for carbon-based hole-transport-layer-free perovskite solar cells

Enhanced Efficiency and Stability for the Inverted High‐Bandgap Perovskite Solar Cell via Bottom Passivation Strategy

Efficient, stable, and fully printed carbon-electrode perovskite solar cells enabled by hole-transporting bilayers

Greatly enhanced power conversion efficiency of hole-transport-layer-free perovskite solar cell via coherent interfaces of perovskite and carbon layers

Back interface management by multifunctional composite carbon nanospheres electrode for efficient and stable HTL-free carbon-based perovskite solar cells

Constructing 2D passivation layer on perovskites based on 3-chlorobenzylamine enables efficient and stable perovskite solar cells

In Situ Back‐Contact Passivation Improves Photovoltage and Fill Factor in Perovskite Solar Cells

Improved 3D-2D Perovskite for Efficient Perovskite Photovoltaics with Low-Temperature Carbon Electrodes

Improved Interfacial Contact between "Perovskite/Electron‐Transport‐Layer" by Hydrophilic Molecule to Achieve Efficiency > 14%, Carbon‐electrode Basing, Hole‐Conductor‐Free, Low‐temperature Mesoscopic Perovskite Solar Cells

Fully Printed High‐Performance Quasi‐Two‐Dimensional Perovskite Solar Cells via Multifunctional Interfacial Engineering

Efficient and stable perovskite solar cells fabrication in open air through adopting a dye interlayer

Double Perovskite Interlayer Stabilized Highly Efficient Perovskite Solar Cells

Low Temperature Processed Fully Printed Efficient Planar Structure Carbon Electrode Perovskite Solar Cells and Modules

Vacuum-Assisted Drying Process for Screen-Printable Carbon Electrodes of Perovskite Solar Cells with Enhanced Performance Based on Cuprous Thiocyanate as a Hole Transporting Layer

Back interface engineering by 2D layered N–Ti 3 C 2 in low-cost carbon based all-inorganic hole transport layer free perovskite solar cells

High‐Efficiency and Stable Perovskite Solar Cells via Buried Interface Modification with Multi‐Functional Phosphorylcholine Chloride

Salt‐Based Catalyzer to Aid Heterogeneous Nucleation Enabling >23% Efficient Electron‐Transport‐Layer‐Free Perovskite Solar Cells

Carbon Electrodes for Perovskite Photovoltaics: Interfacial Properties, Meta‐Analysis, and Prospects

Highly Stable Carbon-Based Perovskite Solar Cell with a Record Efficiency of over 18% Via Hole Transport Engineering