Abstract:Abstract The working condition of the rail transit components such as bogies is complicated, so the high comprehensive performance of composite parts is desperately required. However, existing pure three‐dimensional braided or laminated composites have been unable to satisfy the cooperative demand of in‐plane and interlaminar properties. In this paper, a novel design of three‐dimensional braided/unidirectional (3D/UD) hybrid composite is proposed to balance the in‐plane (tensile, compression, bending), interlaminar (interlaminar shear, low‐speed impact) properties of the composite. The effects of different 3D/UD mixing ratio and layup sequence on the mechanical properties and damage mechanism of hybrid composites were studied by the parametric analysis of the experimental test results, and the comprehensive mechanical properties of the hybrid structure were optimized by COPRAS evaluation method. The results show that the larger the proportion of unidirectional layer, the better the mechanical property in‐plane, but the worse interlayer property. In addition, the change of layup sequence induces a complex nonlinear relationship between 3D/UD mixing ratio and mechanical properties. Combined with microscopic failure characterization results, it is found that the sandwich structure and the addition of uniformly distributed interfacial layer can improve the mechanical properties of the hybrid composite. The optimization results show that the sandwich structure hybrid composite UD 6 /3D/UD 6 with the best balance between in‐plane and interlaminar properties was selected by COPRAS. Compared with pure 3D composites, the comprehensive mechanical properties of UD 6 /3D/UD 6 are increased by 53.9%, which provides a reference for the structural design of hybrid composites in the future. Highlights A novel design of 3D/UD hybrid composite is proposed to balance the in‐plane and interlaminar properties. The influence regularity of 3D/UD mixing ratio and layup sequence on properties of hybrid composites were obtained. The mixing failure mechanism of interlayer and in‐plane was revealed. The optimal structure UD 6 /3D/UD 6 under complex working conditions was obtained by COPRAS.

Fabrication and braiding angle effect on the improved interlaminar shear performances of 3D braided sandwich hybrid composites

Short Beam Shear Behavior and Failure Characterization of Hybrid 3D Braided Composites Structure with X-ray Micro-Computed Tomography

Study on in-plane compression properties and numerical modeling of three dimensional five-directional braided composites

A novel design of three‐dimensional/unidirectional hybrid composites to balance in‐plane and interlaminar mechanical properties

Compressive Failure Characteristics of 3D Four-Directional Braided Composites with Prefabricated Holes

A Comparative Study on Interlaminar Properties of L-shaped Two-Dimensional (2D) and Three-Dimensional (3D) Woven Composites

X-ray microtomography analysis of the damage mechanisms in 3D circular braided carbon fiber/epoxy resin composite tubes under axial impact compression

Investigation of parameterized braiding parameters and loading directions on compressive behavior and failure mechanism of 3D four-directional braided composites

Thermo-mechanical response of 3D braided composites with different braiding angles under high strain rate punch shear loading

Experimental Investigation of Z-pin Insertion Angles on the Mechanical Behavior and Failure Mechanism of Compression after Impact for CFRP Laminates

Novel processing technology and mesoscopic geometric modeling of a new three-dimensional (3D) braided composite and the study on its longitudinal mechanical properties

Investigation and prediction of laminate quality and interlaminar mechanical performance of the tufted sandwich composites with different core structures

Numerical investigation of tensile behavior of three-dimensional six-directional braided composites

High strain rate impact effect and failure behavior of 3D six-directional braided composites

Mechanical Characterization and Impact Damage Assessment of Hybrid Three-Dimensional Five-Directional Composites

Layout design and mechanical behavior of 3D printed intralayer hybrid continuous carbon/glass fiber composites

Unit-cell geometry and mechanical properties of three-dimensional seven-directional braided composites

Analysis of in-plane compression failure mechanism in carbon fiber braided composite with different off-axial angles

Experimental and numerical study of in-plane compressive properties and failure of 3D six-directional braided composites with large braiding angle

Experimental Analysis of the Low-Velocity Impact and CAI Properties of 3D Four-Directional Braided Composites after Hygrothermal Aging

Assessment of 3D woven near‐net‐shaped I‐sections for aeronautical applications: Weave design, manufacture, and mechanical properties under multiple loading conditions