Abstract:Three-dimensional braided composites (3D-BCs) have better specific strength and stiffness than two-dimensional planar composites (2D-PCs), so they are widely used in modern industrial fields. In this paper, two kinds of 3D four-directional braided composites (3D4d-BCs) with different braided angles (15°, denoted as H15, and 30°, denoted as H30) were subjected to hydrothermal aging treatments, low-velocity impact (LVI) tests, and compression after impact (CAI) tests under different conditions. This study systematically studied the hygroscopic behavior and the effect of hygrothermal aging on the mechanical properties of 3D4d-BC. The results show that higher temperatures and smaller weaving angles can significantly improve the moisture absorption equilibrium content. When the moisture absorption content is balanced, the energy absorption effect of 3D4d-BC is better, but the integrity and residual compression rate will be reduced. Due to the intervention of oxygen molecules, the interface properties between the matrix and the composite material will be reduced, so the compressive strength will be further reduced. In the LVI test, the peak impact load of H15 is low. In CAI tests, the failure of H15 mainly occurs on the side, and the failure form is buckling failure. The main failure direction of H30 is 45° shear failure.

What problem does this paper attempt to address?

This paper mainly discusses the low-velocity impact and post-compression performance of three-dimensional four-directional braided composite materials (3D4d-BC) after hygrothermal aging. In the study, the authors conducted hygrothermal aging treatment on two different weaving angles (15 degrees and 30 degrees) of 3D4d-BC, followed by low-velocity impact (LVI) testing and compression after impact (CAI) testing. Through these experiments, they systematically studied the moisture absorption behavior of the materials and the effects of hygrothermal aging on their mechanical properties. The study found that higher temperatures and smaller weaving angles significantly increased the moisture absorption equilibrium content of the materials. However, when reaching moisture absorption equilibrium, although the energy absorption effect of 3D4d-BC is good, its integrity and residual compression ratio will decrease. Due to the intervention of oxygen molecules, the interface properties between the matrix and the composite material are weakened, resulting in a further decrease in compression strength. In the LVI testing, the samples with a weaving angle of 15 degrees showed lower peak impact load, with failures mainly occurring on the side in the form of flexural failure; while the samples with a weaving angle of 30 degrees mainly experienced 45-degree shear failure. The paper also analyzes how the hygrothermal environment affects the physical and mechanical properties of composite materials and points out that current research mainly focuses on the moisture absorption behavior of resin matrix and its impact on performance degradation. Through experimental and numerical simulation methods, the study investigated the changes in the mechanical properties of materials under different weaving angles in complex environments and proposed that these results have guiding significance for engineering testing and the establishment of more efficient and realistic numerical models. In summary, this paper attempts to address the following questions: How do the low-velocity impact and post-compression performance of 3D four-directional braided composite materials change under hygrothermal aging conditions, and how does this change interact with environmental factors.

Experimental Analysis of the Low-Velocity Impact and CAI Properties of 3D Four-Directional Braided Composites after Hygrothermal Aging

Study on in-plane compression properties and numerical modeling of three dimensional five-directional braided composites

An Experimental Investigation of the Mechanism of Hygrothermal Aging and Low-Velocity Impact Performance of Resin Matrix Composites

Research on the Aging Effects of Adhesive and Composites on the Degradation Mechanism of Composite Adhesive Joints in Thermal-Humidity-Cycles for Automobiles

Longitudinal compression fatigue properties of 3D five-directional braided composites at different temperatures

Impact compression damages of 3D braided composites with/without axial yarns after thermo-oxidative ageing

X-ray microtomography analysis of the damage mechanisms in 3D circular braided carbon fiber/epoxy resin composite tubes under axial impact compression

Experimental and numerical study of in-plane compressive properties and failure of 3D six-directional braided composites with large braiding angle

Experimental study on the fabrication, high-temperature properties and failure analysis of 3D seven-directional braided composites under compression

Mechanical Characterization and Impact Damage Assessment of Hybrid Three-Dimensional Five-Directional Composites

Effect of temperature and cyclic hygrothermal aging on the interlaminar shear strength of carbon fiber/bismaleimide (BMI) composite

A novel mechanical behavior and failure mechanism analysis of 3D six-directional braided composites in liquid nitrogen subjected to compression

Transverse bending fatigue behaviors and failure mechanisms of 3D five-directional braided composites at different temperatures

High strain rate impact effect and failure behavior of 3D six-directional braided composites

Analysis of in-plane compression failure mechanism in carbon fiber braided composite with different off-axial angles

Fabrication and braiding angle effect on the improved interlaminar shear performances of 3D braided sandwich hybrid composites

Experimental and numerical investigation on compression after impact behavior of hygrothermal aged CFRP laminates

Compressive Failure Characteristics of 3D Four-Directional Braided Composites with Prefabricated Holes

Mesoscale analysis of aging mechanical behaviors of 3D woven composites

Effects of hygrothermal and thermal aging on the low-velocity impact properties of carbon fiber composites

Thermo-mechanical response of 3D braided composites with different braiding angles under high strain rate punch shear loading