Abstract:The influence of Mo (10‐40at.%) additions to Cr‐8at.%Si was systematically studied by producing arc melted alloys and analyzing the as‐cast and annealed microstructures as well as the oxidation resistances. The majority of the alloys contained a solid solution A2 matrix with the intermetallic A15 = (Cr,Mo)3Si phase. The oxidation resistance was tested by thermogravimetric analysis (TGA) at 1200 °C in air for 50 and 100 h. Samples were characterized by XRD, SEM and EPMA (WDS). The studied Cr‐xMo‐8Si alloy series showed a beneficial effect of Mo on the corrosion behavior of the annealed arc melted alloys exposed at 1200 °C in air. An increased amount of A15 led to the formation of a continuous SiO2 scale beneath the Cr2O3 layer during high temperature exposure. The internal SiO2 layer inhibited further internal oxidation of the A15 phase. Prior annealing also influenced the oxidation behavior of the alloys. Higher annealing temperatures, resulted in an overall reduced fraction of the A15 phase, as well as coarsening, but also showed a more uniform size and distribution of the precipitates, which seems to benefit the formation of a protective duplex oxide scale. Cr‐25Mo‐8at.%Si annealed at 1350 °C for 100 h, showed the most promising oxidation behavior after exposure in air at 1200 °C for 100 h. For all of the investigated Mo contents, no nitridation was observed when compared to the Cr‐8Si reference composition. The oxide scale adhesion also was improved. For Mo >25 at.% no spallation was observed. Evaluation of the TGA data showed it follows the paralinear law, with both the growth rate, kp, and volatilization rate, kv, of Cr2O3 being reduced by adding 10‐25 at.% Mo. A binary Cr/Mo‐Si phase diagram was generated for the studied alloy series in order to determine accurate annealing conditions and estimate the stability range of the metastable σ phase. This article is protected by copyright. All rights reserved.

Microstructure, mechanical properties and tribocorrosion characteristics of (Mo1-xCrx)5Si3 alloys

Structural, mechanical and tribocorrosion performances of CrMoSiN coatings with various Mo contents in artificial seawater

Structure and tribocorrosion behavior of CrMoSiCN nanocomposite coating with low C content in artificial seawater

Influence of TiC contents on the microstructure, mechanical properties, and oxidation behavior of Mo–10Si–8B alloys

THE INFLUENCE OF Mo‐CONTENT AND ANNEALING ON THE OXIDATION BEHAVIOUR OF ARC‐MELTED Cr‐xMo‐8Si ALLOYS

Microstructure, wear and corrosion behavior of high-entropy alloy coatings: The concentration of Mo element and the dual effect of σ-CrMo phase

The enhancement of individual friction and corrosion properties of CrSiN coatings by Mo doping in seawater

Tribocorrosion characteristics of CrMoSiCN/Ag coatings on Ti6Al4V alloys in seawater

Influence of Al and Mo on microstructure and tribological behaviors of Co-based superalloy

Effects of metalloid Si on the microstructure and mechanical properties of Fe36Ni36Cr10Mo1Al17-XSiX alloys

Structure, corrosion, and tribological properties of CrSiN coatings with various Si contents in 3.5% NaCl solution

Microstructure, Mechanical and Tribological Properties of CrSiC Coatings Sliding Against SiC and Al2O3 Balls in Water

Microstructure and mechanical properties of a Mo-toughened Mo 3 Si-based in situ nanocomposite

Microstructure, mechanical properties and tribo-corrosion mechanism of (CrNbTiAlVMo) x N 1-x coated 316 L stainless steel in 3.5 wt.% NaCl solution

Effects of Al substitution with Si and Sn on tribological performance of Ti3AlC2

Tailoring the tribology property and corrosion resistance of selective laser melted CoCrMo alloys by varying copper content

Corrosion and friction behaviours of MoSi 2 /MoS 2 nanoparticles incorporated tinted coating on Ti6Al4V alloy

Effect of Si on Phase Equilibria, Mechanical Properties and Tribological Behaviour of Al-Cu Alloy

Effect of Mo on microstructure, mechanical and corrosion properties of FeCrNiMnMox high-entropy alloys

Electrochemical corrosion and tribological properties of CrMoCN coatings sliding against Al2O3 balls in artificial seawater

The Microstructures and Wear Resistance of CoCrFeNi2Mox High-Entropy Alloy Coatings