Abstract:In the current work, novel Al-rich Al 90-X Cu 10 Si x (x = 2.5 at%, 5 at%, 7.5 at%) ternary alloys were used to evaluate the effect of Si on Al-Cu alloy in an effort to design and develop new lightweight metal alloys with unique microstructure as well as superior mechanical and good wear resistance properties. The solidification behaviour of the studied alloy was predicted by thermodynamic simulation using the ThermoCalc software and compared with experimental results. The microstructure of the studied Al-rich ternary alloys reveals the presence of dendritic phases (i.e., L → L + α-Al) followed by peritectic reaction (i.e., L + α-Al → Al 2 Cu) or eutectic reaction (i.e., L → α-Al + θ-Al 2 Cu) and finally the evolution of ternary eutectic reaction (i.e., L → α-Al + θ-Al 2 Cu + β-Si) for the investigated Al-Cu-Si alloys. It is found that the hardness increased from 150 ± 6.64 HV to 221.9 ± 6.81 HV with the addition of Si from 2.5% to 7.5%. The least wear scar depth of 48 μm is obtained for Al 87.5 Cu 10 Si 7.5 alloy, signifying better wear resistance properties as compared to other alloys. The wear property is found to be 14.2 KN-m/mm 3 for AlCuSi 7.5 alloy, which is better as compared to the wear properties of AlCuSi 2.5 alloy (i.e., 6.9 KN-m/mm 3 ) at a particular load of 5 N. It is also observed that the wear resistance and microhardness properties increase with the addition of Si % with the slight reduction of tensile strength from 240 MPa to 215 MPa.

Effects of Al substitution with Si and Sn on tribological performance of Ti3AlC2

Effect of V Doping on the High Temperature Tribological Properties of (ti1−xvx)3alc2 Solid Solutions Sliding Against Different Counterparts

High Strengthening Effects and Excellent Wear Resistance of Ti3Al(Si)C2 Solid Solutions

Tribological performance of Ti3SiC2 enhanced Ni3Al matrix composites

Ordered Metal Substitution in Ti3AlC2 and the Effect on Tribological Behaviors in a Wide Temperature Range

Effect of Si on Phase Equilibria, Mechanical Properties and Tribological Behaviour of Al-Cu Alloy

Effect of Sliding Speed and Applied Load on Dry Sliding Tribological Performance of TiAl Matrix Self-lubricating Composites

Investigation of Tribological and Mechanical Performances of Ti‐based Self‐Lubricating Composites Containing SnAgCu and Al2O3

Effect of Ag and Ti3SiC2 on Tribological Properties of TiAl Matrix Self-lubricating Composites at Room and Increased Temperatures

Tribological Properties of Ti3SiC2 Coupled with Different Counterfaces

Effect of Ti3SiC2 replacing graphite on the microstructure and properties of Cu-Sn matrix composites

Influence of Ti 3SiC 2 content on tribological properties of NiAl matrix self-lubricating composites

Tribological properties of TiAl-Ti 3 SiC 2 composites

Effect of Ti3SiC2 Content on Tribological Behavior of Ni3Al Matrix Self-Lubricating Composites from 25 to 800 °C

Influence of Ti3AlC2 content and load on the tribological behaviors of Ti3AlC2p/Al composites

Effects of Ti3SiC2 on microstructure and properties of TiC0.4 enhanced TiAl matrix composites

Influence of Mo doping on the tribological behavior of Ti3AlC2 ceramic at different temperatures

Tribological characteristics of new series of Al-Sn-Si alloys

Investigation of the preparation and tribological behavior of a frictional interface covered with sinusoidal microchannels containing SnAgCu and Ti3SiC2

The effect of titanium addition on the microstructure, mechanical and tribological properties of Ni3Si alloys prepared by powder metallurgy method

Mechanical properties and wear behavior of Tin+1(Al, A)Cn (A = Ga, In, Sn, n = 1, 2) via quasi-high-entropy of single atomic thick A layer