Abstract:Copper-nickel alloys have received much attention in the last decades due to their high electrical, thermal, mechanical, and magnetic properties which mainly depend on their composition. In this paper, copper-nickel alloy coatings onto indium tin oxide substrate were elaborated by electrodeposition in pulsed current mode with optimized current density and deposition time. The electrodeposition is subsequently followed by thermal treatment under controlled atmosphere. The surface morphology and the chemical analysis of the elaborated coatings were assessed by scanning electron microscopy associated to x-ray microanalysis. Their structural analysis was performed by x-ray diffraction, and the Vickers microhardness test was conducted to examine their mechanical properties. Moreover, the adhesive strength of the copper-nickel coatings was evaluated using a progressive scratch test, while a multi-pass scratch test was employed to assess their wear resistance. The results showed that the copper-nickel coating obtained with optimized current density (− 20 mA/cm 2 ) and heat treated at 600 °C for 1 h under controlled atmosphere exhibits high mechanical properties; the microhardness increases from 133 to 280 HV, and the adhesion strength from 32 to 203 MPa. On the other hand, optimized electrodeposition conditions followed by thermal treatment led to thinner characteristic XRD pics of Cu-Ni coating indicating an increase in crystallinity from 12 nm to 44 nm. Mechanical characteristics underlined a high resistance to scratches, a decrease in the friction coefficient, and an increase in the dissipated energy which reaches 20 J for heat-treated Cu-Ni coating. These results highlighted a homogeneity in morphology, and low porosity improving the CuNi coatings adhesion strength to the substrate.

Investigation on the effect of nickel and nickel-chromium alloy pulse current plating on copper substrate

Study of the Effect of Current Density on the Metallurgical Properties of AlFeCrNiTi High Entropy Alloy Coating Produced by Pulse Plating

Structure and corrosion property of pulse electrodeposited nanocrystalline nickel-tungsten-copper alloy coating

Heat Treatment Effects on the Microstructural and Mechanical Properties of Electrodeposited Cu-Ni Coatings

The influence of pulse parameters on Zn-Ni alloy coatings plated on AZ91 magnesium alloy

Process for Nickel-Phosphorous Pulse Electroplating and Corrosion Resistance of the Alloy Coating

Effect of Pulse Parumeters on Structure and Properties of NickelCoating

Deposition of nickel films on polycrystalline copper alloy with various current densities from watts solution

Effect of Pulse Electrical Parameters on Performance of Deposited Copper Coatings with Citrate System at Room Temperature

Surface morphology and crystal orientation of electrodeposited tungsten coatings with different pulse parameters

Corrosion Studies on Pulse Reverse Ni-Mo Coatings Electrodeposited on Cu Substrate

Effect of Current Density on Zn-Ni-Mn Alloy Coating Prepared by Pulse Electroplating

Evaluation of corrosion resistance of electrodeposited nanocrystalline Ni–Fe alloy coatings

Study on Electroplating Time of Pulse Electroplating Ni-Cr-Mo Alloy Coating

Investigation on the Electrochemical Catalysis Properties of Ni-decorated Nanoporous Copper Formed by Hybrid Laser Deposition

Plating of Nickel on Copper-based

Electrochemical behavior and electro-crystallization mechanism of Cu-Ni/Nano-Al 2 O 3 coating with a deposition current density dependence

Effect of the Pulse Duty Cycle on the Microstructure and Properties of a Jet Electrodeposited Nanocrystalline Copper Coating

Preparation and Investigation of Ni–Co–P Alloy Coatings Using Jet Electrodeposition with Varying Pulse Parameters

Influence of Average Current Density and Pulse Frequency on Morphology and Structure of Pulse-reverse Current Electroplated Ni Plating

Study on Pulse Electroplating of Ni-Cr-Mn Alloy Coatings