Abstract:Various brittle phases are present in commercial cast aluminum alloys, which strongly influence their mechanical behavior. Among these, silicon precipitates are nearly omnipresent, as Si is a common alloying element. In secondary alloys, usually Fe-containing phases cannot be avoided, and they tend to degrade the mechanical properties. The interaction between the silicon phase and the failure-critical intermetallic phase in the Al-Si-Fe phase system (β- Al5FeSi ) is studied in this paper in high resolution. A model alloy AlSi10Fe0.7 was defined, which is composed of a large grain Al-matrix, Si-precipitates and the plate-like β- Al5FeSi phase. The goal of the study was to identify "hot spots" in the microstructure from which cracks may initiate under mechanical loading. The main tool was a deformation analysis via digital image correlation in the SEM (SEM-DIC). This allows the identification and tracking of developing strain localizations at different potential crack initiation sites with a high resolution as well as capturing an overview over the whole specimen. An adapted frame averaging script minimized measurement errors induced by drift. The SEM-DIC results show that the deformation field is governed by the elastic incompatibility of the microstructural constituents. Crack initiation occurs because of the detachment of the Si + β- Al5FeSi phase boundary. Cracks then cross the phase boundary and propagate along twin boundaries in the β- Al5FeSi phase. Final failure is caused by linking fractured brittle plate-like particles.

Correlative synchrotron absorption edge tomography and microtomography provide insights into the effect of element distribution within intermetallic phases on the fracture behaviour of cast Al-Si alloys

Cracking in a Fe–25Mn–3Si–3Al Steel

Synchrotron X-ray tomography investigation of 3D morphology of intermetallic phases and pores and their effect on the mechanical properties of cast Al-Cu alloys

Evolution of the Second-Phase Particles and Their Effect on Tensile Fracture Behavior of 2219 Al-xCu Alloys

3-D Microstructural Distribution and Mechanical Analysis of HPDC Hypereutectic Al-Si Alloys via X-Ray Tomography

Multi-component Phase-Field Simulation of Microstructural Evolution and Elemental Distribution in Fe–Cu–Mn–Ni–Al Alloy

Crack Configuration Feature and Fracture Surface Difference for High Pressure Die Casting Hypereutectic Al-Si Alloys in High Cycle Fatigue

In-situ investigation of damage mechanisms in duplex AlCoCrFeNi2.1 high entropy alloy

Quantitative Anisotropic Damage Mechanism in a Forged Aluminum Alloy Studied by Synchrotron Tomography and Finite Element Simulations

SEM-DIC characterization of the damage mechanism of an AlSi10Fe0.7 casting alloy on the microstructure scale

Multi-Dimensional Revealing the Influence Mechanism of the δ Phase on the Tensile Fracture Behavior of a Nickel-Based Superalloy on the Mesoscopic Scale

3D Characterisation of the Fe-rich intermetallic phases in Al-5%Cu alloys by synchrotron X-ray microtomography and skeletonisation

In-Situ SEM Observation on Fracture Behavior of Titanium Alloys with Different Slow-Diffusing β Stabilizing Elements

Three-dimensional Quantitative in Situ Study of Crack Initiation and Propagation in AA 6061 Aluminum Alloy Sheets Via Synchrotron Laminography and Finite-Element Simulations

In situ 3D characterization of high temperature fatigue damage mechanisms in a cast aluminum alloy using synchrotron X-ray tomography

3D Characterization of a Nanostructured Al-Cu-Mg Alloy

Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology

Superalloys fracture process inference based on overlap analysis of 3D models

Fracture Behavior of a High Pressure Die Casting AlSi10MnMg Alloy with Varied Porosity Levels

In-Situ Observation of Fracture Behavior of Ti-Aluminide Multi-Layered Composites Produced by a Hybrid Sintering Process

In-situ investigation on the anisotropic behavior of the additively manufactured dual-phase Ti-6Al-4V alloy