Abstract:A high-temperature multi-axial test is carried out to characterize the thermo-mechanical behaviour of a 3D-woven SiC/SiC composite aeronautical part under loads representative of operating conditions. The sample is L-shaped and cut out from the part. It is subjected to severe thermal gradients and a superimposed mechanical load that progressively increases up to the first damage. The sample shape and its associated microstructure, the heterogeneity of the stress field and the limited accessibility to regions susceptible to damage require non-contact imaging modalities. An in situ experiment, conducted with a dedicated testing machine at the SOLEIL synchrotron facility, provides the sample microstructure from computed micro-tomographic imaging and thermal loads from infrared thermography. Experimental constraints lead to non-ideal acquisition conditions for both measurement modalities. This article details the procedure of correcting artefacts to use the volumes for quantitative exploitation (i.e. full-field measurement, model validation and identification). After proper processing, despite its complexity, the in situ experiment provides high-quality data about a part under realistic operating conditions. The influence of the mesostructure on fracture phenomena can be inferred from the tomography in the damaged state. Experiments show that the localization of damage initiation is driven by the geometry, while the woven structure moderates the crack propagation. This study widens the scope of in situ thermo-mechanical experiments to more complex loading states, closer to in-service conditions.

In situ 3D characterization of high temperature fatigue damage mechanisms in a cast aluminum alloy using synchrotron X-ray tomography

3D characterization and modeling of low cycle fatigue damage mechanisms at high temperature in a cast aluminum alloy

Three-dimensional Quantitative in Situ Study of Crack Initiation and Propagation in AA 6061 Aluminum Alloy Sheets Via Synchrotron Laminography and Finite-Element Simulations

In situ synchrotron ultrasonic fatigue testing device for 3D characterisation of internal crack initiation and growth

In Situ Scanning Electron Microscopy Analysis of Effect of Temperature on Small Fatigue Crack Growth Behavior of Nickel-Based Single-Crystal Superalloy

Characterization of internal fatigue cracks in aluminum alloys by simulation of phase contrast tomography

In-situ SEM Investigation on Fatigue Behaviors of Additive Manufactured Al-Si10-Mg Alloy at Elevated Temperature

Fatigue Crack Segmentation and Characterization of Additively Manufactured Ti‐6Al‐4V Using X‐Ray Computed Tomography

In-situ SEM study on fatigue crack behavior of a nickel-based single crystal alloy at 950 °C and 1050 °C

2D and 3D characterization of oxidation‐fatigue mechanisms in an advanced Ni‐based superalloy: Effects of microstructure and elevated temperature

3-D Microstructural Distribution and Mechanical Analysis of HPDC Hypereutectic Al-Si Alloys via X-Ray Tomography

In situ tomographic study of a 3D-woven SiC/SiC composite part subjected to severe thermo-mechanical loads

On the fatigue small crack behaviors of directionally solidified superalloy DZ4 by in situ SEM observations

High-temperature Fatigue Crack Propagation Study of Superalloy GH4169 by Single-Lens 3D Digital Image Correlation

On the Fatigue Short Crack Behaviors of Directionally Solidified Superalloy Dz4 by in Situ Sem Observations

Low cycle fatigue response and fracture mechanism in a novel Al-3.5Si-0.5Mg-0.4Cu casting alloy

In-Situ Characterization of Microstructural Changes in Alloy 718 during High-Temperature Low-Cycle Fatigue

In-situ Observation Technology and Application of Fatigue Crack Initiation and Propagation for Cast Magnesium Alloys

Damage accumulation during high temperature fatigue of Ti/SiCf metal matrix composites under different stress amplitudes

Effect of temperature on the fatigue cracking mechanisms in A356 Al alloy

Fatigue cracking behavior and life assessment of TC11 titanium alloy in very high cycle regime at two working temperatures