Abstract:High-precision and power-efficient sensor interfaces have become increasingly ubiquitous as they form an integral part of multiple fast-growing sectors such as instrumentation control, medical devices, and agricultural automation. Much progress has been recently made in direct-digitization sensor readout circuits (DD-RO). By skipping the instrumentation amplifier (IA) and connecting the ADC directly to the sensor, this architecture reduces system-level complexity compared to conventional IA plus ADC solutions. However, several challenges must be considered. First, in the absence of an IA, it requires a high dynamic range (>90dB) ADC to process the cross-scale input signals and disturbances spanning from several μV to hundreds of mV while retaining excellent sensitivity and linearity, which would usually entail excessive power dissipation. Such demanding DR can be relaxed by a spectrum-shaping $\Delta-\Delta\Sigma$ ADC [1] (Fig. 1). However, $\Delta-\Delta\Sigma$ ADCs are better suited to the spectral characteristic of bioelectrical signals and disturbances (electrode offset, power-line interference, and motion artifact), whose amplitudes decrease approximately with frequency. Second, conventional ADCs typically exhibit finite input impedance that hampers their direct interaction to high-impedance sensors due to the deterioration of total common-mode rejection ratio (T-CMRR) and gain accuracy. Prior art DD-ROs rely on a positive feedback loop (PFL) [2] or pre-charging buffers [3] for impedance boosting, but the former requires dedicated manual calibration while the latter suffers from additional noise, power, and area overhead. Alternatively, a $\Delta\Sigma$ ADC employing the $\mathrm{G}_{\mathrm{m}}-\mathrm{C}$ integrator provides high input impedance (Fig. 1 bottom left), and $\mathrm{G}_{\mathrm{m}}$ can be linearized by degeneration [2], [4]–[6] or fully differential transconductors embedded in current feedback [7] [8] (Fig. 1 bottom right). However, $\mathrm{G}_{\mathrm{m}}$ often dissipates more power to accommodate out-of-range input signals while retaining linearity.

A Simple Digital Readout Circuit for Differential Resistive or Capacitive Sensors

A fully differential analog read-out circuit for differential capacitive sensors

An Energy-Efficient Capacitively Biased Diode-Based Temperature Sensor in 55-nm CMOS

A 103.6Db-Sndr 760Mvpp-Input-range 7.8Gω-Input-impedance Direct-Digitization Sensor Readout with Pseudo-Differential Transconductors and Dummy DAC

A High-Accuracy, High-Speed Interface Circuit for Differential-Capacitance Transducer

Direct Current to Digital Converter (DIDC): A Current Sensor

Fully-Differential Low-Offset Interface For Capacitive Sensors

A Low Cost, High Resolution Interface Circuit for Differential Capacitance Transducer

A 9.84–73.2 Nj, 0.048 Mm2 Time-Domain Impedance Sensor That Provides Values of Resistance and Capacitance

A Compact Sensor Readout Circuit with Combined Temperature, Capacitance and Voltage Sensing Functionality

A Digital Readout Cmos Design For Capacitive Sensors Using On-Chip Variable Sense Capacitor Arrays

Double Input Capacitively Coupled Contactless Conductivity Detector with Phase Shift

A 9-Bit Resistor-Based Highly Digital Temperature Sensor with a SAR-Quantization Embedded Differential Low-Pass Filter in 65-Nm CMOS with a 2.5- $\mu$ S Conversion Time

Energy-Efficient Capacitive Sensor Interfaces

A 9-Bit Resistor-Based All-Digital Temperature Sensor with a SAR-Quantization Embedded Differential Low-Pass Filter in 65nm CMOS Consuming 57pj with a 2.5 Μs Conversion Time.

A Touch Sensor Controller IC Adopting Differential Measurement for Projected Capacitive Touch Panel Systems

A Continuous-Time Voltage Readout for SiC Micromechanical Capacitive Pressure Sensor.

A Charge Delta-Sigma Modulator for Differential-Capacitance Sensors

An Energy-Efficient 15-Bit Capacitive-Sensor Interface Based On Period Modulation

A Closed-Loop Sigma Delta Modulator For Micromechanical Capacitive Sensors

An energy-efficient 15-bit capacitive sensor interface.