Abstract:Due to the increasing demands for lightweight parts in various fields, such as bicycle, automotive, aircraft and aerospace industries, hydroforming processes have become popular in recent years. Since tubular materials during tube hydroforming are under a bi-axial even tri-axial stress state, which is different from that in the tensile test, it is necessary to test the mechanical properties of the material under bi-axial stress state. Tube bulging test is an advanced method for characterizing the mechanical properties of tubular materials under bi-axial stress state. But there are excessive physical quantities in the theoretical model of tube bulging test for testing the mechanical properties of tubes under bi-axial stress state which are difficult to be obtained during the experiment. In order to solve the problems, a method for directly testing the mechanical properties of tubes under bi-axial stress state was proposed in this work, which will be referred to as "one point method". Because of circular model is characterized by a dominant function expression, theoretical models of both the pole axial curvature radius and the pole thickness during bulging test are derived under supposing the geometrical models for bulging zone as circular. Thus, the mechanical properties of tubes under bi-axial stress state can be obtained only through measuring the bulging height at the pole point during the bulging test, which laid the foundation for the establishment of a simple and reliable method for testing the mechanical properties of the tube online. Based on the above proposed method, the extruded aluminum alloy tubes AA6061 were tested. The results showed that both the pole axial curvature radius and the pole thickness during bulging test can be expressed as display functions pertaining to the bulging height at the pole point. For the theoretical model of the pole axial curvature radius, as the bulging rate increases, the prediction accuracy increases at beginning, and decreases at the end when using circular as the theoretical geometrical models for bulging zone. The prediction accuracy is the highest as the bulging rate is about 13%, the prediction accuracy decreases after the bulging rate is more than 20%. Fortunately, the overall prediction error is small. The maximum error does not exceed +/-0.9%. The prediction accuracy of the pole thickness using the theoretical model is almost unaffected by the specimen geometry. When the ratios of length to diameter and diameter to thickness change, the difference is very small, the prediction error is not more than 0.8%. This is very helpful to ensure the accuracy of mechanical testing under bi-axial loading conditions. Using the "one point method", the stress and strain components along the circumferential and axial directions can be simultaneously measured, this laid the foundation for further analysis of the anisotropic property impacting on the flow and subsequent yield under complex stress state.

Measurement and analysis of deformation behavior of thermoplastic elastomer tube subjected to biaxial tensile stress under loading and unloading

Identification of True Stress-Strain Curve of Thermoplastic Polymers under Biaxial Tension

A New Method for Directly Testing the Mechanical Properties of Anisotropic Materials in Bi-Axial Stress State by Tube Bulging Test

Elastomeric tubes with self-regulated distension

Investigation of in-plane visco-deformation in PMMA indentation via TLV model calibrated with tensile specimens

A Simple Constrained Uniaxial Tensile Apparatus for in Situ Investigation of Film Stretching Processing

Optimizing Pure Shear Experiment to Properly Characterize the Shear Properties of Thin-Walled Aluminum Alloy Tubes

Tracking the evolution of the morphology and stress distribution of SIS thermoplastic elastomers under tension using atomic force microscopy

Simulation Analysis of Equibiaxial Tension Tests for Rubber-like Materials

Design and Calibration of A New Biaxial Extensometer for Radial Deformation Measurement under Hydro-Compression Loading

Device for plastic compression of long-dimensional cylindrical samples in linear stress conditions

Bending of Pseudoelastic NiTi Tubes

Modeling of the stress–strain responses and deformation patterns of superelastic NiTi tubes subjected to biaxial loadings

Analysis of strain state prismatic samples for mechanical testing of the biaxial stretching method digital image correlation

Experimental Study of the Biaxial Cyclic Behavior of Thin-Wall Tubes of NiTi Shape Memory Alloys

Multiaxial Plastic Deformation of Zircaloy-4 Nuclear Fuel Cladding Tubes

Experimental investigations on extruded 6063 aluminium alloy tubes under complex tension-compression stress states

Identification of Anisotropic Coefficients in the Non-Principal Axis Directions of Tubular Materials Using Hole Bulging Test

A novel Hopkinson tension bar system for testing polymers under intermediate strain rate and large deformation

Experimental Study on Characterizing Damage Behavior of Thermoplastics

Device and method for investigation of mechanical properties of the materials under high-strain rate tensile load