Abstract:Surface texturing has been shown to reduce friction and improve durability in mechanical face seals and metal forming operations, and lightly loaded thrust bearings. However, the success has been limited to conformal contacts and low load high speed operating conditions, i.e. hydrodynamic lubrication dominated regime. Both experiments and numerical simulations have shown that textural patterns, under higher loading and/or slower speeds may increase friction and even cause the lubrication film collapse. Specific designs of surface texture pattern, as its shape, depth and density, are required for different lubrication regimes. Our own study has shown (Hsu et al 2014 J. Phys. D: Appl. Phys. 47 335307) that large/shallow dimple reduces friction in hydrodynamic lubrication regime, whereas small/deep dimple shows benefit in mixed/boundary lubrication regimes (if the textural designs can provides hydrodynamic/hydrostatic lift forces to reduce the machine loading). In considering an engine component typically experiences duty cycles that may cross various lubrication regimes, a multiscale surface texture design appears attractive. This type of mixed shape texturing combines textures designed for low load, high speed operating conditions and the textures that are designed for high load, low speed operations. In this paper, two types of multiscale surface texture designs are presented. Ball-on-three-flats (BOTF) wear tester (under high loading conditions) is used to evaluate the performance of these multiscale texture designs along with the baselines of un-textured surfaces under the same surface preparation procedures. Two texture designs with only a single shape dimples are included in the study. Results suggest that multiscale surface texture design not only further reduces friction in comparison to the textures with single shape dimples, but also shows the effectiveness across hydrodynamic regimes to the mixed lubrication regimes.

Method of Enhancing Lubrication Performance of the Engine Based on Optimal Dimples of Partial Textures

Optimizing the Parameters of the Partial Textures of the Crankpin Bearing to Enhance the Lubrication Performance of an Engine

Improving engine's lubrication based on optimised partial micro-textures

Lubrication efficiency of crankpin bearing using square-cylindrical textures of partial textures optimized by genetic algorithm

Multi-objective Optimization of Micron-Scale Surface Textures for the Cylinder/valve Plate Interface in Axial Piston Pumps

Optimal design of micro-dimples on crankpin bearing surface for improving engine’s lubrication and friction

Design and Fabrication of the Lubricating Dimple of the Headface Sliding Bearing with Phyllotactic Pattern

Evaluation and Optimization of Axial Piston Pump Textured Slipper Bearings with Spherical Dimples Based on Hybrid Genetic Algorithm

Self-adaptive surface texture design for friction reduction across the lubrication regimes

Design and optimization of textures on the surface of crankpin bearing to improve lubrication efficiency and friction power loss of engine

Influence of Microdimple on Lubrication Performance of Textured Plunger Pump

Effect of Micro-Dimple Texture on the Tribological Performance of Brass with Titanium Nitride (TiN) Coating under Oil-Lubricated Conditions

Numerical Investigation of the Tribological Performance of Micro-Dimple Textured Surfaces under Hydrodynamic Lubrication

Study on the effects of the textured surface to improve the performance of cylinder block/valve plate interfaces

Optimization of surface texture distribution on the thrust bearing using the mass-conserving cavitation boundary condition: Theory and experiments

The Effect of Dimple Shapes on Friction of Parallel Surfaces

CFD Analysis of the Effect of Dimples and Cylinder Liner Honing Groove on the Tribological Characteristics of a Low Displacement Engine

Lubrication Adaptability to the Variations of Combustion Modes by Texturing Cylinder Liner in Engines

Effects of the array modes of laser-textured micro-dimples on the tribological performance of cylinder liner–piston ring

Theoretical Analysis on Hydrodynamic Lubrication of Cylinder Micro-dimple Surface Texture

Multi-objective Optimization of Surface Texture for the Slipper/swash Plate Interface in EHA Pumps