Abstract:Surface texturing has been shown to reduce friction and improve durability in mechanical face seals and metal forming operations, and lightly loaded thrust bearings. However, the success has been limited to conformal contacts and low load high speed operating conditions, i.e. hydrodynamic lubrication dominated regime. Both experiments and numerical simulations have shown that textural patterns, under higher loading and/or slower speeds may increase friction and even cause the lubrication film collapse. Specific designs of surface texture pattern, as its shape, depth and density, are required for different lubrication regimes. Our own study has shown (Hsu et al 2014 J. Phys. D: Appl. Phys. 47 335307) that large/shallow dimple reduces friction in hydrodynamic lubrication regime, whereas small/deep dimple shows benefit in mixed/boundary lubrication regimes (if the textural designs can provides hydrodynamic/hydrostatic lift forces to reduce the machine loading). In considering an engine component typically experiences duty cycles that may cross various lubrication regimes, a multiscale surface texture design appears attractive. This type of mixed shape texturing combines textures designed for low load, high speed operating conditions and the textures that are designed for high load, low speed operations. In this paper, two types of multiscale surface texture designs are presented. Ball-on-three-flats (BOTF) wear tester (under high loading conditions) is used to evaluate the performance of these multiscale texture designs along with the baselines of un-textured surfaces under the same surface preparation procedures. Two texture designs with only a single shape dimples are included in the study. Results suggest that multiscale surface texture design not only further reduces friction in comparison to the textures with single shape dimples, but also shows the effectiveness across hydrodynamic regimes to the mixed lubrication regimes.

Multi-objective Optimization of Micron-Scale Surface Textures for the Cylinder/valve Plate Interface in Axial Piston Pumps

Multi-objective Optimization of Surface Texture for the Slipper/swash Plate Interface in EHA Pumps

Optimization Tool Based on Multi-Objective Adaptive Surrogate Modeling for Surface Texture Design of Slipper Bearing in Axial Piston Pump

Research on Multi-Objective Optimization of Low Pulsation Unloading Damping Groove of Axial Piston Pump

Multi-Objective Optimization of Multistage Centrifugal Pump Based on Surrogate Model

Multi-objective Optimization Design of Sliding Bearing of High-speed Centrifugal Pump Based on Lubrication Characteristics Analysis

Structural Multi-objective Optimization Design of Air-suspending Frictionless Pneumatic Cylinders

Evaluation and Optimization of Axial Piston Pump Textured Slipper Bearings with Spherical Dimples Based on Hybrid Genetic Algorithm

Analysis and Optimization on U-shaped Damping Groove for Flow Ripple Reduction of Fixed Displacement Axial-Piston Pump

Effect of Surface Texture on Wear Reduction of the Tilting Cylinder and the Valve Plate for a High-Speed Electro-Hydrostatic Actuator Pump

Multi-Point Optimization on the Diffuser of an Axial Flow Pump

Noise Reduction of an Axial Piston Pump by Valve Plate Optimization

Optimization of Cross Angle Based on the Pumping Dynamics Model

Effects of Chevron Micro-Textures on Tribological and Lubricating Performance of Cylinder Block/Valve Plate Interface in Axial Piston Pumps

Investigation on the Radial Micro-Motion about Piston of Axial Piston Pump

Raising the Speed Limit of Axial Piston Pumps by Optimizing the Suction Duct

Self-adaptive surface texture design for friction reduction across the lubrication regimes

Flow Ripple Reduction of Axial-Piston Pump by Structure Optimizing of Outlet Triangular Damping Groove

Investigation on Structural Optimization of Anti-Overturning Slipper of Axial Piston Pump

Design Optimization of Valve Plate of a Bi-directional Axial Piston Pump for Electro Hydrostatic Actuation Systems

Coupled Evolution of Piston Asperity and Cylinder Bore Contour of Piston/cylinder Pair in Axial Piston Pump