Abstract:Surface texturing has been shown to reduce friction and improve durability in mechanical face seals and metal forming operations, and lightly loaded thrust bearings. However, the success has been limited to conformal contacts and low load high speed operating conditions, i.e. hydrodynamic lubrication dominated regime. Both experiments and numerical simulations have shown that textural patterns, under higher loading and/or slower speeds may increase friction and even cause the lubrication film collapse. Specific designs of surface texture pattern, as its shape, depth and density, are required for different lubrication regimes. Our own study has shown (Hsu et al 2014 J. Phys. D: Appl. Phys. 47 335307) that large/shallow dimple reduces friction in hydrodynamic lubrication regime, whereas small/deep dimple shows benefit in mixed/boundary lubrication regimes (if the textural designs can provides hydrodynamic/hydrostatic lift forces to reduce the machine loading). In considering an engine component typically experiences duty cycles that may cross various lubrication regimes, a multiscale surface texture design appears attractive. This type of mixed shape texturing combines textures designed for low load, high speed operating conditions and the textures that are designed for high load, low speed operations. In this paper, two types of multiscale surface texture designs are presented. Ball-on-three-flats (BOTF) wear tester (under high loading conditions) is used to evaluate the performance of these multiscale texture designs along with the baselines of un-textured surfaces under the same surface preparation procedures. Two texture designs with only a single shape dimples are included in the study. Results suggest that multiscale surface texture design not only further reduces friction in comparison to the textures with single shape dimples, but also shows the effectiveness across hydrodynamic regimes to the mixed lubrication regimes.

Optimization Tool Based on Multi-Objective Adaptive Surrogate Modeling for Surface Texture Design of Slipper Bearing in Axial Piston Pump

Multi-objective Optimization of Micron-Scale Surface Textures for the Cylinder/valve Plate Interface in Axial Piston Pumps

Multi-objective Optimization of Surface Texture for the Slipper/swash Plate Interface in EHA Pumps

Multi-objective Optimization Design of Sliding Bearing of High-speed Centrifugal Pump Based on Lubrication Characteristics Analysis

Multi-Objective Optimization of Multistage Centrifugal Pump Based on Surrogate Model

Evaluation and Optimization of Axial Piston Pump Textured Slipper Bearings with Spherical Dimples Based on Hybrid Genetic Algorithm

Investigation on Structural Optimization of Anti-Overturning Slipper of Axial Piston Pump

Surrogate-based optimization design for surface texture of helical pair in helical hydraulic rotary actuator

Optimization Design Of The Inner Radius Of The Sealing Surface Of Slipper

Numerical Optimization of the Groove Texture Bottom Profile for Thrust Bearings

Optimizing the Parameters of the Partial Textures of the Crankpin Bearing to Enhance the Lubrication Performance of an Engine

Numerical Simulation of Overturning Phenomenon of Axial Piston Pump Slipper Pair

Effects of Surface Roughness on the Mixed Thermal Elstohydrodynamic Lubrication Characteristics of Surface Textured Slipper Bearing in Axial Piston Pump

Research on Multi-Objective Optimization of Low Pulsation Unloading Damping Groove of Axial Piston Pump

Effect of surface square textures on the physical field of static and dynamic pressure thrust bearings and multi-objective optimization

Design and optimization of textures on the surface of crankpin bearing to improve lubrication efficiency and friction power loss of engine

Simulation Study on Bearing Lubrication Mechanism and Friction Characteristics of the Biomimetic Non-Smooth Surface of a Cross-Scale, Second-Order Compound Microstructure

Investigation on the Radial Micro-Motion about Piston of Axial Piston Pump

Multi-objective optimization of surface texture shape in fluid mechanical face seals using mass-conserving cavitation boundary condition

Self-adaptive surface texture design for friction reduction across the lubrication regimes

Performance Optimization for High Speed Axial Piston Pump Considering Cylinder Block Tilt