Abstract:Surface texturing has been shown to reduce friction and improve durability in mechanical face seals and metal forming operations, and lightly loaded thrust bearings. However, the success has been limited to conformal contacts and low load high speed operating conditions, i.e. hydrodynamic lubrication dominated regime. Both experiments and numerical simulations have shown that textural patterns, under higher loading and/or slower speeds may increase friction and even cause the lubrication film collapse. Specific designs of surface texture pattern, as its shape, depth and density, are required for different lubrication regimes. Our own study has shown (Hsu et al 2014 J. Phys. D: Appl. Phys. 47 335307) that large/shallow dimple reduces friction in hydrodynamic lubrication regime, whereas small/deep dimple shows benefit in mixed/boundary lubrication regimes (if the textural designs can provides hydrodynamic/hydrostatic lift forces to reduce the machine loading). In considering an engine component typically experiences duty cycles that may cross various lubrication regimes, a multiscale surface texture design appears attractive. This type of mixed shape texturing combines textures designed for low load, high speed operating conditions and the textures that are designed for high load, low speed operations. In this paper, two types of multiscale surface texture designs are presented. Ball-on-three-flats (BOTF) wear tester (under high loading conditions) is used to evaluate the performance of these multiscale texture designs along with the baselines of un-textured surfaces under the same surface preparation procedures. Two texture designs with only a single shape dimples are included in the study. Results suggest that multiscale surface texture design not only further reduces friction in comparison to the textures with single shape dimples, but also shows the effectiveness across hydrodynamic regimes to the mixed lubrication regimes.

Multi-objective Optimization of Surface Texture for the Slipper/swash Plate Interface in EHA Pumps

Multi-objective Optimization of Micron-Scale Surface Textures for the Cylinder/valve Plate Interface in Axial Piston Pumps

Multi-objective Optimization Design of Sliding Bearing of High-speed Centrifugal Pump Based on Lubrication Characteristics Analysis

Effect of Surface Texture on Wear Reduction of the Tilting Cylinder and the Valve Plate for a High-Speed Electro-Hydrostatic Actuator Pump

Optimization Tool Based on Multi-Objective Adaptive Surrogate Modeling for Surface Texture Design of Slipper Bearing in Axial Piston Pump

Investigation on Structural Optimization of Anti-Overturning Slipper of Axial Piston Pump

Optimization Design Of The Inner Radius Of The Sealing Surface Of Slipper

Piston Surface Design to Improve the Lubrication Performance of a Swash Plate Pump

Dynamic lubrication model for slipper/swashplate of high-speed electro-hydrostatic actuator pump

A New Coupled Dynamic Model to Study the Vibration and Lubrication Characteristics of Slipper/Swash-Plate Interface in an Axial Piston Pump

A Hybrid of CFD and PSO Optimization Design Method of the Integrated Slipper/swashplate Structure in Seawater Hydraulic Axial Piston Pump

Self-adaptive surface texture design for friction reduction across the lubrication regimes

Study on the Surface Micro-texture of Blades of Continuous Rotary Electro-hydraulic Servo Motor

Optimization and Influence of Micro-Chamfering on Oil Film Lubrication Characteristics of Slipper/Swashplate Interface Within Axial Piston Pump

Wear Modelling of Slipper/swashplate Pair for Highspeed Piston Pump under Transient Lubrication Conditions

Evaluation Method and Experimental Verification of Hydrodynamic Lubrication Performance of Different Texturing

Study on the Load-Carrying Capacity of Surface Textured Slipper Bearing of Axial Piston Pump

Investigation on mixed thermalelstohydrodynamic lubrication behavior of slipper/swash plate interface in water hydraulic axial piston pump

Impact Evaluation Approach of a Texture Cross Section Shape on Hydrodynamic Lubrication Performance

Numerical simulation on hydrodynamic lubrication performance of bionic multi-scale composite textures inspired by surface patterns of Subcrenata and Clam shells

Hydrostatic bearing groove multi-objective optimization of the gear ring housing interface in a straight-line conjugate internal meshing gear pump