Abstract:The influence of oscillating laser frequency and oscillation diameter on the stability and porosity of laser-arc hybrid welding of titanium alloys were investigated. The microstructure and basic mechanical properties of oscillating laser-arc hybrid welded joints were revealed. The results show that the oscillating laser significantly improved the macroscopic morphology of the joints, reducing the porosity from 5.48 % to 0.12 %. In the conventional laser-arc hybrid welding process, the number of keyhole surface closures was more and the time of droplet transition was longer, resulting in poor process stability. When the frequency was 150 Hz and the diameter was 1.5 mm at oscillating laser conditions, the number of keyhole closures within 200 ms was significantly reduced to 5 times compared to the conventional laser-arc hybrid welding (23 times). The droplet transition was stable, which resulted in a more stable hybrid welding process. In addition, after one oscillation cycle, the forward distance of the laser was relatively short, which can reopen the smaller pores generated in the previous cycle, leading to a significant reduction in porosity. When the frequency and diameter of oscillation decreased, the fluctuation for keyhole morphology was greater and the droplet transition was instability, resulting in an increase in porosity; When the oscillation increased, the fluctuation of the keyhole outer diameter was larger and the penetration depth decreased, which was not conducive to the welding of medium-thick plates. In the oscillating laser-arc hybrid welding process, columnar crystals in the middle of the molten pool grew towards the surface, reducing the segregation of impurities in the weld center. As a result, the elongation percentage of the joints was improved by 36.58 % compared to the conventional laser joints.

Effect of welding stability on process porosity in laser arc hybrid welding of dissimilar steel

Droplet Transfer Induced Keyhole Fluctuation and Its Influence Regulation on Porosity Rate during Hybrid Laser Arc Welding of Aluminum Alloys

Numerical Study of Keyhole Instability and Porosity Formation Mechanism in Laser Welding of Aluminum Alloy and Steel

Simulation of the Effect of Keyhole Instability on Porosity during the Deep Penetration Laser Welding Process

Investigation on Porosity Suppression in Deep-Penetration Laser Welding by Using Computational Fluid Dynamics

Investigation of the Inhibition Mechanism of Process Porosity in Laser-MIG Hybrid-Welded Joints for an Aluminum Alloy

Relationship Between Molten Pool Behavior and Keyhole-Induced Porosity in Pulsed Laser-arc Hybrid Welding of Magnesium Alloy

Analysis of Droplet Transfer and Porosity Characteristics in Laser-MAG Hybrid Welding of Edge Joint

Porosity Formation Mechanism and Its Prevention in Laser Lap Welding for T-Joints

Research Status of Stability in Dynamic Process of Laser-Arc Hybrid Welding Based on Droplet Transfer Behavior: A Review

Study on the influence of Al-Si welding wire on porosity sensitivity in laser welding and process optimization

Experimental Investigation and Numerical Study on the Elimination of Porosity in Aluminum Alloy Laser Welding and Laser–GMA Welding

Stability analysis and porosity inhibition mechanism ofoscillating laser-arc hybrid welding process for medium-thick plate TC4 titanium alloy

Investigation on the Effects of Shielding Gas on Porosity in Fiber Laser Welding of T-joint Steels

MECHANISMS OF THE POROSITY FORMATION DURING THE FIBER LASER LAP WELDING OF ALUMINIUM ALLOY

Effects of Welding Parameters on Weld Porosity During CO2 Laser Welding of Die-Cast Magnesium Alloys

Mechanism analysis on suppressing porosity in laser-MIG hybrid welding of aluminum alloy via external magnetic field

Mitigation of Porosity Defects in Fiber Laser Welding under Low Vacuum

Porosity inhibition of aluminum alloy by power-modulated laser welding and mechanism analysis

Effect of the Welding Direction on the Microstructural Characterization in Fiber Laser-Gmaw Hybrid Welding of 5083 Aluminum Alloy

An Investigation on the Effects of Side Assisting Gas Flow and Metallic Vapour Jet on the Stability of Keyhole and Molten Pool During Laser Full-Penetration Welding