Abstract:The dense WC-M2 high-speed steel matrix composites (WC-M2 HSS MMCs) with different WC content were prepared by mechanical alloying and vacuum sintering process. Tungsten Carbide (WC) with 0, 2, 5, 8, and 10 (by weight %) were dispersed in the matrix. The effects of WC content on the densification mechanism, phase composition, microstructure, fracture morphology, and mechanical and wear properties of the sintered composites were systematically investigated. The experimental results showed that at a vacuum sintering temperature of 1260 °C, the composite material specimens achieved near-full densification, with predominant phases being Martensitic, M 7 C 3 , M 6 C, M 2 C, MC, WC, α-Fe, and γ-Fe. Reasonable WC addition has improved grain uniformity and reduced micro-defects, which enhanced the overall mechanical properties. With an increase in WC content, the hardness and relative density of the composites showed a gradual increase, whereas transverse rupture strength and impact toughness initially improved but subsequently decreased. The friction coefficient displayed an initial increase followed by a decrease, while the wear rate showed an opposite trend. The impact fracture morphology is dominated by the interfacial separation between the WC particle phase and the binder phase, supplemented by the plastic tearing of the binder phase. The impact toughness mainly depended on the fracture of the binder phase. During crack propagation, both intergranular and transgranular fractures exist, of which the intergranular fracture prevails and coarse grains are more prone to transgranular fracture. With 5 wt.% WC, the steel matrix composites obtained peak mechanical performance, with impact toughness, bending strength, and hardness measuring 13.2 J cm −2 , 1584.3 MPa, and 780.9 HV, respectively, which also yielded the highest wear resistance.

Application of U-FAST Technology in Sintering of Submicron WC-Co Carbides

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Sintering of the WC-6%Co cemented carbides for improved mechanical and cutting performance using Micro-FAST

Spark Plasma Sintering of Fine-Grained WC-Co Composites

Rapid synthesis of ultrafine WC-Co cemented carbides by in-situ reactions and spark plasma sintering

Ultrafast high-temperature sintering (UHS) of WC and WC-containing ZrB 2

Ultrafast fabrication of W/Cu composites using flash sintering

Room temperature stability, structure and mechanical properties of cubic tungsten carbide in flash sintered products

Ultrafine WC-Co cemented carbide with enhanced mechanical properties prepared by oscillating sinter forging

Mechanical Properties and Microstructural Behaviour of Microwave Sintered WC–Co

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism

Ultrafine WC-Ni cemented carbides fabricated by spark plasma sintering

Fabrication and Properties of Axisymmetric WC/Co Functionally Graded Hard Metal via Microwave Sintering

Comparative Study on Microstructure and Mechanical Properties of Coarse-grained WC-based Cemented Carbides Sintered with Ultrafine WC or (W+C) as Additives

High-Entropy-Alloy CoFeNiCr Bonded WC-Based Cemented Carbide Prepared by Spark Plasma Sintering

Microstructure and properties of coarse WC-10CoCrFeMnNi cemented carbide by mechanical alloying and hot pressing sintering

Enhancement of the mechanical properties of ultrafine-grained WC-Co cemented carbides via the in-situ generation of VC

Spark Plasma Sintering of Ultrafine WC-5%Co Cemented Carbide Composite Powders

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

Investigation of the Influence of High Speed Sintering Regimes on the Structure and Properties of WC Based Carbide Composites with High Entropy Bonding

Microstructure Evolution and Hardness Improvement of WC-Co Composites Sintered with Fe Substituting Part of Co Binder