Abstract:In this study, we investigated the effects of nanostructured composite powders (WC-Ni), nickel binder content, and sintering techniques on the morphology and mechanical properties of tungsten carbide. An alternative low-temperature gas-solid reaction route with a short reaction time was employed to produce nanostructured composite powders with 5 and 15 wt% Ni. The powders were consolidated using spark plasma sintering (SPS) and conventional vacuum furnace sintering at temperatures of 1350 °C and 1450 °C. The composite powders were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and particle size measurements. The expansion/contraction of the compacted nanocomposite powders was studied through dilatometric analysis. The composite powders exhibited a uniform distribution of Ni, in both compositions. For the WC-5 wt% Ni nanocomposite powders, the average crystallite sizes for WC and Ni were 41.6 nm and 46.2 nm, respectively. While, for the WC-15 wt% Ni nanocomposite, the crystallite sizes for WC and Ni were 45.6 and 38.4 nm. The sintered composites were evaluated through XRD, SEM, measurements of density and Vickers hardness. The enhanced sinterability of the nanostructured powders enabled their consolidation into (WC-Ni) hard metal with densities approaching the theoretical relative density of 96.07 %, even with low binder content (5 wt% Ni). This is attributed to the uniform distribution of Ni and an extensive Ni-WC interface present prior to sintering. The SPS process at 1350 °C produced sintered bodies (WC-5 wt% Ni and WC-15 wt% Ni) with higher Vickers hardness (2322 HV and 1512 HV, respectively) and superior microstructural quality compared to samples produced by conventional vacuum furnace techniques. These results demonstrated that the mechanical properties of the system WC-Ni processed by SPS are superior to those obtained by vacuum furnace. Therefore, WC-Ni hard metals processed by this approach is a promising alternative to conventional hard metals (WC-Co) for a wide range of applications.

Investigation of the Influence of High Speed Sintering Regimes on the Structure and Properties of WC Based Carbide Composites with High Entropy Bonding

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

Effects of Metal Binder Content and Carbide Grain Size on the Microstructure and Properties of SPS Manufactured WC–Fe Composites

An investigation of the peculiarities of high-speed sintering of plasma chemically synthesized tungsten carbide nanopowders with increased oxygen content

Study on Effect of High-Entropy Alloy Binder on Microstructure and Properties of WC Cemented Carbide Doped with Rare Earth Oxide

Effects of milling time and sintering temperature on the mechanical properties of 8 wt% WC/AlCoCrFeNiTi 0.5 high entropy alloy matrix composite

Spark Plasma Sintering of Fine-Grained WC-Co Composites

Combined effect of SiC and carbon on sintering kinetics, microstructure and mechanical properties of fine-grained binderless tungsten carbide

Experimental investigation on fabrication, characterization and properties of spark plasma sintered alumina-based tungsten carbide composites reinforced by carbon nanotubes

Microstructural and Mechanical Characterization of Colloidal Processed WC/(W5Vol%Ni) via Spark Plasma Sintering

Influence of powder mixing processes and WC contents on microstructure, shrinkage behavior, and mechanical properties of WC-Si3N4 composites

Spark Plasma Sintering Preparation of Tungsten Carbide-Reinforced Iron-Based Composite Materials: Wear Resistance Performance and Mechanism

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism

Synthesis and characterization of WC-FeCr base alloy composite produced by spark plasma sintering

Spark Plasma Sintering of Ultrafine WC-5%Co Cemented Carbide Composite Powders

High-Entropy-Alloy CoFeNiCr Bonded WC-Based Cemented Carbide Prepared by Spark Plasma Sintering

Characterization of the elastic modulus of ceramic–metal composites with physical and mechanical properties by ultrasonic technique

Optimisation of sintering parameters for bonding nanocrystalline cemented tungsten carbide powder and solid high strength steel

Enhanced properties of hard metal WC-Ni processed from nanostructured powders

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites

A study of mechanical properties and WEDM machinability of spark plasma sintered ZrB2-B4C ceramic composites