Abstract:The purpose of the work is to establish the influence of the basic elements of the chemical composition of steel for railway axles on the features of the formation of the primary structure. The problem of macrosegregation of alloying elements, which occurs during the solidification of a cast billet during continuous casting, remains relevant; it is the subject of countless experiments and theoretical judgments. A large percentage of these studies are devoted to carbon segregation, which is understandably highly relevant for the production of carbon steels. The relationship of processing, microstructure and properties indicates that the morphology and properties of the various phases at the microscopic level are largely closely related to the macroscopic behavior of materials. Basic knowledge about the mechanism of segregation shows that this is a very complex effect and it is necessary to take into account a wide range of factors that affect the continuous casting process. Due to the limited solubility of individual elements in the crystal lattice of steel, during the solidification of the melt, the residual liquid is enriched, resulting in the formation of micro- and macrosegregations (segregations, heterogeneities). The aim of the work is to reveal the influence of chemical elements on the formation of reverse segregation. As part of this work, pilot batches of steel samples were made and analyzed, which are used for the manufacture of railway axles - steel grades OS according to DSTU 31334, F according to AAR M 101 and EA1N according to EN 13261. Separate emphasis was placed on the ratio of content in steel Si and Mn. The formation of the so-called "reverse segregation" zone, observed in the studied ingots, is most likely due to the contamination and gas contamination of steel. The nature of the formation of this zone coincides with the features of the formation of places of contact between the branches of higher-order dendrites. It is established that the presence of structural heterogeneity reduces the mechanical properties. It has been shown for the first time that an increase in the ratio of Mn to Si content in axial steels of the EA1N, OC, and F grades contributes to an increase in the gas saturation of the steel and the appearance of anomalous structures.

Dendrite Structure, Spot Segregation and Banded Defect of Gear Steel in Continuous Casting and Rolling Process

Revealing the evolution mechanism from spot segregation to banded defect above the austenitization temperature

Formation and effects of banded structures in 55SiCrA spring steel wire rod

Central Segregation of High-carbon Steel Billet and Its Heredity to the Hot-rolled Wire Rods

Macro-segregation in Cast Bloom of Gear Steel and Its Formation Mechanism

Effect of Cr/Mn segregation on pearlite—martensite banded structure of high carbon bearing steel

Morphology characteristics of solidification structure in high-carbon steel billet based on fractal theory

An Application of Fractal Theory to Complex Macrostructure: Quantitatively Characterization of Segregation Morphology

Effect of Segregation on Hot Deformation Behavior of Gcr15 Bearing Steel in Continuous Casting

Segregation and carbide evolution in AISI D2 tool steel produced by curved continuous casting

Precipitation, Growth, and Aggregation Behavior of Primary Carbides during Continuous Casting of 6Cr13 Slabs

Study on Micro Segregation of High Alloy Fe–Mn–C–Al Steel

Carbon Macrosegregation Heredity of Cast Bloom of Special Steel and Microstructure Characteristics of Its Rolled Bar

Study on the positive segregation in columnar-to-equiaxed transition zone

The Role of Elements Partition and Austenite Grain Size in the Ferrite-Bainite Banding Formation during Hot Rolling

Formation of the macrostructure depending on the city and the ratio of the main components in railway steel ingots

Effect of Solidification Segregation on Microstructure and Mechanical Properties of a Ni-Cr-Mo-V Steel Weld Metal

Effect of layered heterogeneous microstructure design on the mechanical behavior of medium carbon steel

Research on the surface modification and microstructure evolution during gear profile grinding based on cellular automaton

Quantitative Characterization of Solidification Structure in Different Sections for Calculating the Permeability in Actual High-Carbon Steel Billet

Microstructure Characteristics and Wear Performance of a Carburizing Bainitic Ferrite + Martensite Si/Al-Rich Gear Steel