Abstract:Many key forging components of heavy equipment are manufactured by large steel ingots.Macrosegregation in steel ingots is a key defect formed during the solidification process.Over the past few decades,numerical modeling has played a more and more important role in the study of macrosegregation.Various models have been developed and applied to different ingot casting processes.This paper focused on the application of macrosegregation models to the steel ingot.Firstly,the formation mechanism and influencing factors of macrosegregation were introduced.Then,the existing macrosegregation models and their recent development were summarized.Macrosegregation models accounting for such mechanisms as solidification shrinkage-induced flow and mushy zone deformation were analyzed,respectfully.To model macrosegregation due to solidification shrinkage,the key was to solve the free surface.A simple derivation showed that the multi-phase (including gas phase) models were equivalent to the VOF-based segregation models in dealing with the shrinkage-induced flow.Finally,our recent research work on numerical modeling of macrosegregation in steel ingots was illustrated,including application of the developed multi-component and multi-phase macrosegregation model to a 36 t steel ingot,and numerical simulation of multiple pouring process.The carbon and sulphur concentrations at about 1800 sampling points,covering the full section of a 36 t ingot,were measured.By detailed temperature recording,accurate heat transfer conditions between the ingot and mould were obtained.Typical macrosegregation patterns,including the bottom-located negative segregation and the pushpin-like positive segregation zone in the top riser,have been reproduced both in the measurements and the predictions.The carbon and sulphur concentrations predicted by the three dimensional multi-component and multi-phase macrosegregation models agreed well with the measurements,thus proving that the model can well predict the macrosegregation formation in steel ingots.As for the multi-pouring process simulation,the results show a high concentration of carbon at the bottom and a low concentration of carbon at the top of the mould after the multi-pouring process with carbon content high in the first ladle and low in the last ladle.Therefore,the multiple pouring process could get the initial solute distribution with the opposite form of segregation.Such carbon concentration distribution would reduce the negative segregation at the bottom and the positive segregation at the top of the solidified ingot,thus proving the ability of the multiple pouring process for the control of macrosegregation.

Macro-segregation in Cast Bloom of Gear Steel and Its Formation Mechanism

Carbon Macrosegregation Heredity of Cast Bloom of Special Steel and Microstructure Characteristics of Its Rolled Bar

Dendrite Structure, Spot Segregation and Banded Defect of Gear Steel in Continuous Casting and Rolling Process

Effect of feeding strip temperature on macrosegregation in a large continuous casting round bloom

Effect of M-EMS on Carbon Segregation of Gear Steel Round Bar Rolled from Rectangular Bloom

Experimental and Numerical Study of Macrosegregation in a 160 Steel Ingot

Numerical Simulation of Macrosegregation in Steel Ingot Casting

On the Macrosegregation of Continuous Casting of High Carbon Steel Billet with Strand Reduction Process

Three-Dimensional Macrosegregation Model of Bloom in Curved Continuous Casting Process

Modeling of Species Transport and Macrosegregation in Heavy Steel Ingots

Multiphase Modeling of Macrosegregation Formation in Steel Ingot

Carbon Macrosegregation Pattern in 30Cr15Mo1N Ingot: Impact of Pouring Rate

A Numerical Study of the Effect of Multiple Pouring on Macrosegregation in a 438-Ton Steel Ingot

Modelling of Macrosegregation in A 231-Ton Steel Ingot with Multi-Pouring Process

Modelling of Ingot Size Effects on Macrosegregation in Steel Castings

Modelling of macrosegregation in steel ingots: Benchmark validation and industrial application

High-efficiency continuous casting of GCr15 bearing steel bloom based on cooperative control technique of complex electromagnetic stirring and soft reduction

Numerical Study of Macrosegregation in a Large Steel Ingot with Multiple Pouring Process

Gradual-cooling solidification approach to alleviate macrosegregation in large steel ingots

Study on the positive segregation in columnar-to-equiaxed transition zone

Effect of Macrosegregation on the Microstructure and Mechanical Properties of a Pressure-Vessel Steel