Abstract:During the cold drawing process, pearlite lamellae turn to the drawing direction to form ferrite fiber texture; the cementite lamellae are divided into a multilayer structure, and the dissolution of cementite lamellae in some regions results in the lattice expansion of ferrite phase and the occurrence of neck‐down regions in the cementite lamellae. The microstructure, texture, and dislocation configuration of cold‐drawn pearlitic steel wires were investigated by scanning electron microscopy (SEM), electron backscattering diffraction (EBSD), and transmission electron microscopy (TEM). In addition, Fe/Fe3C interface structure at the atomic level was clearly observed and analyzed by high‐resolution TEM (HRTEM), and the microscopic deformation mechanism of cementite lamellae at different drawing strains is revealed. The results show that pearlite lamellae turn to the drawing direction to form ferrite fiber texture, and the cementite and ferrite lamellae are simultaneously thinned with the increase of drawing strain. During the cold drawing process, shear‐bands(S‐bands) are formed in the cementite lamellae; the dislocation of ferrite transits from single slip to multi‐slip stage, and the dislocation density increases. After drawing, the lattice structures of cementite and ferrite phases show the evolution from single‐crystal to polycrystal, and the cementite lamellae are divided into a multilayer structure: central relative large‐size cementite crystal and outside relative small‐size cementite crystal layer; the dissolution of cementite lamellae in some regions results in the lattice expansion of ferrite phase and the occurrence of neck‐down regions in the cementite lamellae.

Formation and effects of banded structures in 55SiCrA spring steel wire rod

A Banding Structure in A Ni-Cu-Si Cast Alloy

The Comprehensive Effect of Controlled Cooling and Si/Mn Elements on the Structure-Property Relationship of a Novel Wire Rod

Effect of Cr/Mn segregation on pearlite—martensite banded structure of high carbon bearing steel

Hierarchical Structures in Cold-Drawn Pearlitic Steel Wire

Dendrite Structure, Spot Segregation and Banded Defect of Gear Steel in Continuous Casting and Rolling Process

EVOLUTIONS OF MICROSTRUCTURE AND FERRITIC MICRO--ORIENTATION AND TEXTURE IN A PEARLITIC STEEL WIRE DURING COLD DRAWING

Evolution of Microstructure and Fe/Fe3C Interface Structure in Cold‐Drawn Pearlitic Steel Wires

Effect of Microstructure and Microtexture on the Mechanical Properties of Small-Strain Cold-Drawn Pearlite Steel Wires

Causes and Control Mechanism of Abnormal Structure in the Center of SWRH82B Wire-Rod-Steel

Characterization and 3D Reconstruction of the Crushing Behavior of SiO2–CaO–Al2O3–MgO Complex Inclusions in Spring Steel with High Basicity Slag Treatment

Effect of White Band on Quality of Billet Cast with F-EMS

Effect of Solidification Segregation on Microstructure and Mechanical Properties of a Ni-Cr-Mo-V Steel Weld Metal

Microstructure Evolution and Mechanical Properties of a Wire-Arc Additive Manufactured Austenitic Stainless Steel: Effect of Processing Parameter

Microstructural Evolution, Strengthening Mechanisms and Strength Structure Relationship in Cold-Drawn Pearlitic Steel Wire

Structure and strength of sub-100 nm lamellar structures in cold-drawn pearlitic steel wire

In-situ investigation of composition segregation and deformation streamline in bainitic steel on mechanical properties

The Method of Eliminating Banded Structure and the Effects of Banded Structure on the Transverse Properties in 20G Steel

INFLUENCE OF INTERNAL CRACKING ON CARBIDE PRECIPITATION IN CONTINUOUS CASTING BLOOM INDUCED BY SOFT REDUCTION TECHNOLOGY AND THE RESULTING SEGREGATED BAND IN HOT-ROLLED WIRE RODS

Influence of Cooling Procedure After Transformation-Temperature-Rising on Microstructure and Property of 82B Wires

Characterization of the Microstructure in Drawn Pearlitic Steel Wires