Abstract:Many key forging components of heavy equipment are manufactured by large steel ingots.Macrosegregation in steel ingots is a key defect formed during the solidification process.Over the past few decades,numerical modeling has played a more and more important role in the study of macrosegregation.Various models have been developed and applied to different ingot casting processes.This paper focused on the application of macrosegregation models to the steel ingot.Firstly,the formation mechanism and influencing factors of macrosegregation were introduced.Then,the existing macrosegregation models and their recent development were summarized.Macrosegregation models accounting for such mechanisms as solidification shrinkage-induced flow and mushy zone deformation were analyzed,respectfully.To model macrosegregation due to solidification shrinkage,the key was to solve the free surface.A simple derivation showed that the multi-phase (including gas phase) models were equivalent to the VOF-based segregation models in dealing with the shrinkage-induced flow.Finally,our recent research work on numerical modeling of macrosegregation in steel ingots was illustrated,including application of the developed multi-component and multi-phase macrosegregation model to a 36 t steel ingot,and numerical simulation of multiple pouring process.The carbon and sulphur concentrations at about 1800 sampling points,covering the full section of a 36 t ingot,were measured.By detailed temperature recording,accurate heat transfer conditions between the ingot and mould were obtained.Typical macrosegregation patterns,including the bottom-located negative segregation and the pushpin-like positive segregation zone in the top riser,have been reproduced both in the measurements and the predictions.The carbon and sulphur concentrations predicted by the three dimensional multi-component and multi-phase macrosegregation models agreed well with the measurements,thus proving that the model can well predict the macrosegregation formation in steel ingots.As for the multi-pouring process simulation,the results show a high concentration of carbon at the bottom and a low concentration of carbon at the top of the mould after the multi-pouring process with carbon content high in the first ladle and low in the last ladle.Therefore,the multiple pouring process could get the initial solute distribution with the opposite form of segregation.Such carbon concentration distribution would reduce the negative segregation at the bottom and the positive segregation at the top of the solidified ingot,thus proving the ability of the multiple pouring process for the control of macrosegregation.

Quantitative Characterization of Solidification Structure in Different Sections for Calculating the Permeability in Actual High-Carbon Steel Billet

An Application of Fractal Theory to Complex Macrostructure: Quantitatively Characterization of Segregation Morphology

Morphology characteristics of solidification structure in high-carbon steel billet based on fractal theory

Numerical Simulation of Macrosegregation Impurities in the Solidifying Continuous Casting Steel Billet

Prediction of Mushy Zone Permeability of Al-4.5wt%Cu Alloy During Solidification by Phase Field Model and CFD Simulation

Numerical Simulation of Macrosegregation in a 535 Tons Steel Ingot with a Multicomponent-Multiphase Model

On the Macrosegregation of Continuous Casting of High Carbon Steel Billet with Strand Reduction Process

Simulation of Macrosegregation in a 36-T Steel Ingot Using a Multiphase Model

Experimental and Numerical Study of Macrosegregation in a 160 Steel Ingot

Numerical Simulation of Macrosegregation in Cast-steel Ingot

Numerical Simulation of Macrosegregation with Solid Deformation During the Solidification of Steel Ingots Using a Single-Phase/Two-Phase Integrated Model

Experimental Measurements for Numerical Simulation of Macrosegregation in a 36-Ton Steel Ingot

Multiphase Modeling of Macrosegregation Formation in Steel Ingot

Numerical Simulation of Macrosegregation in Steel Ingot Casting

Influence of Dendritic Morphology on the Calculation of Macrosegregation in Steel Ingot

Prediction of permeability in mushy zone of Al-4.5 %Mg alloy based on CA-LBM model

Three-dimensional simulation of thermosolutal convection and macrosegregation in steel ingots

Modelling of Macrosegregation in A 231-Ton Steel Ingot with Multi-Pouring Process

Influences of Dendrite Morphologies and Solid-Back Diffusion on Macrosegregation in Directionally Solidified Blade-Like Casting

Three-Dimensional Simulation of Macrosegregation in a 36-Ton Steel Ingot Using a Multicomponent Multiphase Model

Numerical Study of Macrosegregation in a Large Steel Ingot with Multiple Pouring Process