Abstract:316L stainless steel pipes are widely used in the storage and transportation of low-temperature media due to their excellent low-temperature mechanical properties and corrosion resistance. However, due to their low thermal conductivity and large coefficient of linear expansion, they often lead to significant welding residual tensile stress and thermal cracks in the weld seam. This also poses many challenges for their secure and reliable applications. In order to effectively control the crack defects caused by stress concentration near the heat-affected zone of the weld, this paper establishes a thermal elastoplastic three-dimensional finite element (FE) model, constructs a welding heat source, and simulates and studies the influence of process parameters on the residual stress around the pipeline circumference and axial direction in the heat-affected zone. Comparison and verification were conducted using simulation and experimental methods, respectively, proving the rationality of the finite element model establishment. The axial and circumferential residual stress distribution obtained by the simulation method did not have an average deviation of more than 30 MPa from the numerical values obtained by the experimental method. This study also considers the effects of welding energy, welding speed, and welding start position on the pipe's circumferential and axial residual stress laws. The results indicate that changes in welding energy and welding speed have almost no effect on the longitudinal residual stress but have a more significant effect on the transverse residual stress. The maximum transverse residual stress is reached at a welding energy of 1007.4~859.3 J/mm and a welding speed of 6.6 mm/s. Various interlayer arc-striking deflection angles can impact the cyclic phase angle of the transverse residual stress distribution in the seam center, but they do not alter its cyclic pattern. They do influence the amplitude and distribution of the longitudinal residual stress along the circumference. The residual stress distribution on the surface of the pipe fitting is homogenized and improved at 120°.

Welding process optimization for the inner tank of the electric water heater by numerical simulation and experimental study

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

Welding Process Optimization for Steam Generator Divider Plate Against Disbonding of Dissimilar Metal Weld

Numerical Investigation on Stress Distribution and Evolution in 9cr/2.25cr Dissimilar Welded Rotor Undergoing Welding and Heat Treatment

Numerical simulation of residual stress in post internal-welding process of bimetal composite pipe and optimization of welding sequence

Optimization of welding parameters on welding distortion and stress in S690 high-strength steel thin-plate structures

Effect of Process Parameters on Welding Residual Stress of 316L Stainless Steel Pipe

Numerical Simulation of Welding Residual Stress of Tube-to-tubesheet Joint in Heat Exchangers

Effect of Welding Sequence and the Transverse Geometry of the Weld Overlay on the Distribution of Residual Stress in the Weld Overlay Repair of T23 Tubes

Multi-objective optimization of the resistance spot welding process using a hybrid approach

Welding residual stress analysis of the X80 pipeline: simulation and validation

The primary-auxiliary local post-welding heat treatment method to control welding residual stresses for pressure vessels

On Residual Stress and Relief for an Ultra-Thick Cylinder Weld Joint Based on Mixed Hardening Model: Numerical and Experimental Studies

Effect of Local Rapid Cooling Heat Treatment on Residual Stress of Pressure Vessel Inner Wall Welding Layer

3D finite element analysis and optimization of welding residual stress in the girth joints of X80 steel pipeline

Finite Element Analysis of Welding Residual Stress of the Ultra-Thick 13mnnimor Steel Cylinder of a Large EO Reactor Made in China

Precision and Efficiency Sensitivity of Some Key Techniques in Thermo-mechanical Numerical Simulation of Welding Process

Numerical Simulation of Temperature Evolution, Solid Phase Transformation, and Residual Stress Distribution during Multi-Pass Welding Process of EH36 Marine Steel

Study on The Selection of Water Pump of In-service Welding Test-bed

Numerical Simulation Of Fluid Flow And Temperature Field In Keyhole Double-Sided Arc Welding Process On Stainless Steel