Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

The Effect of Amorphous Polysilazane and Infiltration Method on The Densification of SiCf/SiC Composites

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Silicon Carbide/Polysilazane Composite: Effect of Temperature on the Densification, Phase, and Microstructure Evolution

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

Study of the effect of the morphology of initial powders on the structural and dimensional characteristics of SiC-based porous ceramic materials

Influence of polycarbosilane composition on the properties of SiC/SiC composite fabricated by precursor infiltration and pyrolysis process

Effect of polycarbosilane content on microstructures and mechanical properties of short-carbon-fibre-reinforced SiC composites

A Low Cost Preparation of C/SiC Composites by Infiltrating Molten Si into Gelcasted Pure Porous Carbon Preform

Effect of chemical vapor infiltration on the flexural properties of C/C-SiC composites prepared by the precursor infiltration pyrolysis method

Preparation and Formation Mechanism of C/C–SiC Composites Using Polymer-Si Slurry Reactive Melt Infiltration

Infiltration of SiC Preforms with Iron Silicide Melts: Microstructures and Properties

Pressureless Infiltration Preparation of High SiC/Al Ceramic Matrix Composites

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

Gel casting and properties of porous silicon carbide/silicon nitride composite ceramics

Fabrication of 3D-SiC/aluminum alloy interpenetrating composites by DIW and pressureless infiltration

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

C/C–SiC Composites Derived from Single‐source Poly(silylene–acetylene) Precursors

Aqueous Processing, Hot-Pressing and Mechanical Properties of Silicon Carbide with Al2O3 and Y2O3

The Effect of PyC/SiC Compound Interphase on the Properties of PIP SiC/SiC Composite

Slurry‐impregnating hot‐press sintered silicon carbide nanofiber/silicon carbide composites with Al‐B‐C as sintering additives

Effect of polymer infiltration and pyrolysis (PIP) on microstructure and properties of high volume fraction SiC/Al composites prepared by a novel hybrid additive manufacturing