Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Silicon Carbide/Polysilazane Composite: Effect of Temperature on the Densification, Phase, and Microstructure Evolution

Investigation of the effect of pressure, sintering temperature and time on silicon carbide microstructure

Microstructures of Short-Carbon-Fiber-Reinforced Sic Composites Prepared by Hot-Pressing

Effect of polycarbosilane content on microstructures and mechanical properties of short-carbon-fibre-reinforced SiC composites

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride

The Effect of Amorphous Polysilazane and Infiltration Method on The Densification of SiCf/SiC Composites

Microstructure and Mechanical Properties of the Spark Plasma Sintered Tac/Sic Composites: Effects of Sintering Temperatures

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Microstructures and densification of MoSi2–SiC composite by field-activated and pressure-assisted combustion synthesis

PRESSURELESS SINTERING OF SILICON CARBIDE NANOCOMPOSITE CERAMICS

Synthesis of α-SiC/α-SiAlON composites by spark plasma sintering: Phase formation and microstructures development

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Effect of temperature on the structure and mechanical properties of SiC–TiB2 composite ceramics by solid-phase spark plasma sintering

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Microstructure, phase compositions and mechanical properties of slip cast sintered SiC/Si3N4 composites

Preparation of Porous Si2N2O/SiC Ceramics by Microwave Sintering

Sintering Aids and Thermal Conductivity of Polycrystalline SiC

Fabrication, Microstructure, and Properties of SiC/Al 4 SiC 4 Multiphase Ceramics Via an In-Situ Formed Liquid Phase Sintering

Effect of SiC on Microstructure, Phase Evolution, and Mechanical Properties of Spark-Plasma-Sintered High-Entropy Ceramic Composite