Abstract:In the past, Mg-Zn alloys prepared by a two-step manufacturing process of casting plus extrusion have been demonstrated to be a good candidate for biodegradable applications. But, studies on fabricating of Mg-Zn alloys with a single step process of squeeze casting capable of producing porosity-free Mg alloys, which can reduce the cost, are limited. In the present work, Zinc (Zn) addition varying from 1.0 up to 10.0 wt. % was introduced into liquid magnesium. The alloyed liquid was squeeze cast under an applied pressure of 90 MPa. The results of mechanical testing on the squeeze cast Mg-Zn alloys shows that Zn is an effective additive for enhancing their mechanical properties, specifically, tensile and yield strengths at room temperature, but reducing the elongation. While the Zn addition rises from 1.0 to 10.0 wt.%, the ultimate tensile and yield strengths increases to 181.0 MPa and 105.0 MPa from 140.7 MPa and 39.3 MPa, while the elongation-to-failure (e f ) decreases to 3.7% from 6.2%, respectively. The reveal of the as-cast grain structure by an optical microscope (OM) indicates that the high Zn content reduces grain sizes considerably. The microstructures analyzed by a scanning electron microscope (SEM) with the energy dispersive spectroscopy (EDS) show that the secondary MgZn phase forms once Zn is introduced in sufficient amount. The grain refinement and the massive presence of the secondary MgZn phase at the boundaries of the refined grains should be responsible to the enhancement of the strengths and the reduction in the elongation. The developed pressurized casting without employing secondary manufacturing processes such as extrusion or heat treatment exhibits its advantages to enhance the mechanical properties of the Mg alloys with high Zn content over conventional fabrication processes, since high Zn-containing Mg alloys have a long freezing range and tend to form microshrinkage porosity.

Improvement of microstructure, mechanical properties, and corrosion resistance of WE43 alloy by squeeze casting

Comparison of Corrosion Performance of Extruded and Forged WE43 Mg Alloy

Experimental study of squeeze casting of ZK60 magnesium alloy

Microstructure and mechanical properties of WE43 magnesium alloy fabricated by wire-arc additive manufacturing

Microstructure and Mechanical Properties of Squeezing Casting Mg-Nd-Gd-Zn-Zr Alloy

Microstructure and Mechanical Properties of Thick-Walled WE43A Alloy Fabricated by Wire Arc Additive Manufacturing

Effect of Rolling Treatment on Microstructure, Mechanical Properties, and Corrosion Properties of WE43 Alloy

Microstructure and Mechanical Properties of Squeeze Casting Quasicrystal Reinforced AZ91D Magnesium Matrix Composites

Squeeze Cast Mg-Zn Alloys for Bioapplications: Tensile Properties and Microstructure

Study on Microstructure Distribution of Al-Cu-Mg Alloy in Squeeze Casting Process

Microstructure, mechanical properties and fracture behaviors of large-scale sand-cast Mg-3Y-2Gd-1Nd-0.4Zr alloy

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

A comparative study on WE43 magnesium alloy fabricated by laser powder bed fusion coupled with deep cryogenic treatment: Evolution in microstructure and mechanical properties

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Influence of fine-grain and solid-solution strengthening on mechanical properties and in vitro degradation of WE43 alloy

Biodegradation of Az31 and We43 Magnesium Alloys in Simulated Body Fluid

Variation of Corrosion Characteristics and Tensile Performances of WE43 Alloy Under Marine Atmospheric Environment

In vitro corrosion and biocompatibility of phosphating modified WE43 magnesium alloy

Effect of Powder Composition on WE43 Magnesium Alloy Fabricated by Laser Powder Bed Fusion

Mechanical and corrosion properties of full liquid phase sintered WE43 magnesium alloy specimens fabricated via binder jetting additive manufacturing

Study on Pressurized Solidification Behavior and Microstructure Characteristics of Squeeze Casting Magnesium Alloy AZ91D