Abstract:The preparation of large-scale magnesium (Mg) alloy parts by wire arc additive manufacturing (WAAM) has broad application prospects, including automotive and aerospace industries. The chemical composition of Mg alloy wires plays a critical role in determining mechanical properties of WAAM Mg alloys. However, types of Mg alloy wires for WAAM need to be extended, in order to improve mechanical properties. Therefore, in the present work, a novel ATZM31 Mg alloy wire has been prepared and applied to the cold metal transfer (CMT)-WAAM process. This study focuses on understanding the forming quality, microstructure evolution, and mechanical properties of the ATZM31 alloy thin-wall component fabricated by WAAM. The results show that the Mg alloy thin-wall component possesses satisfactory formability, with minor sidewall roughness. The ATZM31 thin-wall component is mainly composed of columnar dendrites and equiaxed dendrites of the α-Mg phase, with the η-Al 8 Mn 5 phase distributes dispersedly at grain boundaries. The area fraction of the η-Al 8 Mn 5 phase is estimated to be ∼0.21% based on the statistical analysis of SEM images. Due to different cooling behaviors, the distribution of grain size along the build direction of the thin-walled component is uneven. The average grain size is ∼46 μm, ∼74 μm and ∼61 μm at the bottom, middle and top of the ATZM31 alloy thin-wall component, respectively. From the substrate to the top of the ATZM31 alloy thin-wall component, the hardness decreases gradually. The ultimate tensile strength along the deposition direction and build direction are ∼225 MPa and ∼214 MPa, respectively, without pronounced anisotropy. The ATZM31 alloy thin-wall component fabricated by WAAM exhibits a comparable ultimate tensile strength to forged AZ31 Mg alloys and weaker anisotropy than wrought Mg alloys.

Microstructure and mechanical properties of WE43 magnesium alloy fabricated by wire-arc additive manufacturing

Microstructure and Mechanical Properties of Thick-Walled WE43A Alloy Fabricated by Wire Arc Additive Manufacturing

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Achieving fully equiaxed grain microstructure and isotropic mechanical properties in wire arc additive-manufactured Mg-Y-Nd-Zr alloys

Wire arc additive manufacturing of a novel ATZM31 Mg alloy: Microstructure evolution and mechanical properties

Microstructure and mechanical properties of wire and arc additive manufactured AZ31 magnesium alloy using cold metal transfer process

Formability, microstructure evolution and mechanical properties of wire arc additively manufactured AZ80M magnesium alloy using gas tungsten arc welding

Microstructure and mechanical properties of AZ31 magnesium alloy prepared using wire arc additive manufacturing

Microstructures and Properties of Al-Mg Alloys Manufactured by WAAM-CMT

Microstructure and Mechanical Properties of Weaving Wire and Arc Additive Manufactured AZ91 Magnesium Alloy Based on Cold Metal Transfer Technique

Effect of heat treatment on the microstructure and mechanical properties of Mg-Gd-Y-Zr alloys fabricated by wire arc additive manufacturing

Wire-arc additive manufacturing of AZ31 magnesium alloy fabricated by cold metal transfer heat source: Processing, microstructure, and mechanical behavior

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

Microstructure and mechanical properties of GTA-based wire arc additive manufactured AZ91D magnesium alloy

Microstructure and mechanical properties of Mg-Gd-Y-Zn-Zr alloy fabricated by cold metal transfer wire arc additive manufacturing

Study on anisotropy of microstructure and mechanical properties of AZ31 magnesium alloy fabricated by wire arc additive manufacturing

Additive manufacturing of high performance AZ31 magnesium alloy with full equiaxed grains: Microstructure, mechanical property, and electromechanical corrosion performance

On the fabrication of finer grain structure through using finer wire diameter for wire arc additive manufacturing of AZ31B magnesium alloy

Printing High-Strength High-Elongation Al4043 Alloy Using UNS A94043 Welding Wires through Wire Arc Additive Manufacturing

Effect of heat treatment on microstructure and mechanical properties of WE43 alloy fabricated by wire arc additive manufacturing