Abstract:During the fabrication of an indium-gallium-zinc oxide (IGZO) thin film transistor (TFT), the thermal process was used to reduce the resistivity of IGZO. The annealing temperature was found to have great influence on the transistor characteristics. At an optimized heat-treatment temperature, the depletion-mode IGZO TFT was fabricated with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage. And the relatively conductive IGZO could directly replace the indium tin oxide as the transparent electrode of the organic light-emitting diode (OLED), reducing the mask count of the backplane for the active-matrix OLED display. INTRODUCTION Thin film transistor (TFT) based on metal oxide (MO), especially, indium-gallium-zinc oxide (IGZO), is considered as a good candidate to fabricate large area backplane for active-matrix organic light-emitting diode (AMOLED) display, due to its high mobility, good uniformity and low off-state current [1]. Our previous study [2] suggested that the resistivity (ρ) of IGZO highly depended on the heat-treatment conditions, such as annealing ambience, temperature, duration and gas permeability of IGZO cover, while the thermal process was often inevitable during the fabrication of IGZO TFT. With the active layer of IGZO covered with the gas-permeable silicon oxide (SiOx), the TFT was subjected to a serious anneals in an oxygen-deficient nitrogen (N2) ambience. With the increasing temperature, although the mobility was enhanced, the turn-on voltage (Von) became more and more negative. At an optimized temperature, the depletion-mode (DM) IGZO TFT with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage was fabricated. Furthermore, such annealing-induced conductive IGZO source/drain regions can be directly used to replace the indium tin oxide (ITO) as the transparent electrode of OLED, reducing the mask count of AMOLED backplane. Annealing-Induced DM IGZO TFT Shown in Figure 1 is the evolution of the schematic cross-section of an IGZO TFT. A gate dielectric of 100 nm silicon oxide (SiOx) was first thermally grown on an n+ silicon substrate, which served as the gate electrode. 10 or 20 nm IGZO film was then room-temperature sputtered using a target of In2O3:Ga2O3:ZnO = 1:1:1 mol% in an atmosphere of 10% oxygen (O2) and 90% argon (Ar). After the patterning of the active-island using the hydrofluoric acid, a passivation layer of 300 nm SiOx was deposited at 300 oC in a plasma-enhanced chemical vapor deposition (PECVD) reactor. The tetraethylorthosilicate (TEOS) and O2 were used as the source gases. The contact holes were then opened and the resulting structure was subjected to a series of anneals, as shown in Figure 1a. Finally, 300 nm aluminum (Al) was deposited and patterned into electrodes (Fig. 1b). These TFTs were measured using an Agilent 4156C semiconductor parameter analyzer. n+ Si 100nm SiOx 300nm SiOx

Process Development of Amorphous Indium Tin Gallium Oxide (ITGO) Thin Film Transistors

Aqueous Solution Derived Amorphous Indium Doped Gallium Oxide Thin-Film Transistors

Study of the Correlation between the Amorphous Indium-Gallium-Zinc Oxide Film Quality and the Thin-Film Transistor Performance

High performance amorphous IGO TFTs grown at low temperature

Performance Improvement of a-In-Ga-Sn-O Thin-Film Transistor with Oxygen Doping by Reactive Sputtering Method

High mobility of IGO/IGZO double-channel thin-film transistors by atomic layer deposition

Annealing-Induced Depletion-Mode Indium-Gallium-Zinc Oxide Thin-Film Transistor and Its Application to Active-Matrix Organic Light-Emitting Diode Display

Comparative Study of Indium Oxide Films for High‐Mobility TFTs: ALD, PLD and Solution Process

Present status of amorphous In–Ga–Zn–O thin-film transistors

Comparative Study of Atomic Layer Deposited Indium-Based Oxide Transistors with a Fermi Energy Level-Engineered Heterojunction Structure Channel through a Cation Combinatorial Approach

Amorphous Indium Tin Oxide Thin-Film Transistors Fabricated by Cosputtering Technique

Influence of indium doping on electrical performance of gallium oxide thin-film transistors

High-Performance Solution-Processed Amorphous InGaZnO Thin Film Transistors with a Metal–Organic Decomposition Method

Argon and Oxygen Gas Flow Rate Dependency of Sputtering-Based Indium-Gallium-Zinc Oxide Thin-Film Transistors

Improvement of device characteristics of plasma-treated indium gallium zinc oxide thin-film transistors through thermal annealing

Scalability and Stability Enhancement in Self-Aligned Top-Gate Indium- Zinc-Oxide TFTs with Al Reacted Source/Drain

Solution-processed amorphous gallium-tin oxide thin film for low-voltage, high-performance transistors

Stability Study of Indium Tungsten Oxide Thin-Film Transistors Annealed under Various Ambient Conditions

High-Performance Amorphous InGaZnO Thin-Film Transistor Gated by HfAlOₓ Dielectric with Ultralow Subthreshold Swing

Stability and gap states of amorphous In-Ga-Zn-Ox thin film transistors: Impact of sputtering configuration and post-annealing on device performance

Impact of electrode materials on the performance of amorphous IGZO thin-film transistors