Abstract:The dense WC-M2 high-speed steel matrix composites (WC-M2 HSS MMCs) with different WC content were prepared by mechanical alloying and vacuum sintering process. Tungsten Carbide (WC) with 0, 2, 5, 8, and 10 (by weight %) were dispersed in the matrix. The effects of WC content on the densification mechanism, phase composition, microstructure, fracture morphology, and mechanical and wear properties of the sintered composites were systematically investigated. The experimental results showed that at a vacuum sintering temperature of 1260 °C, the composite material specimens achieved near-full densification, with predominant phases being Martensitic, M 7 C 3 , M 6 C, M 2 C, MC, WC, α-Fe, and γ-Fe. Reasonable WC addition has improved grain uniformity and reduced micro-defects, which enhanced the overall mechanical properties. With an increase in WC content, the hardness and relative density of the composites showed a gradual increase, whereas transverse rupture strength and impact toughness initially improved but subsequently decreased. The friction coefficient displayed an initial increase followed by a decrease, while the wear rate showed an opposite trend. The impact fracture morphology is dominated by the interfacial separation between the WC particle phase and the binder phase, supplemented by the plastic tearing of the binder phase. The impact toughness mainly depended on the fracture of the binder phase. During crack propagation, both intergranular and transgranular fractures exist, of which the intergranular fracture prevails and coarse grains are more prone to transgranular fracture. With 5 wt.% WC, the steel matrix composites obtained peak mechanical performance, with impact toughness, bending strength, and hardness measuring 13.2 J cm −2 , 1584.3 MPa, and 780.9 HV, respectively, which also yielded the highest wear resistance.

Effect of Wet Milling and Reinforcement Content on Iron-Multi-walled Carbon Nanotube Metal Matrix Composite Fabricated by Conventional Powder Metallurgy

Preparation and Characterization of Hybrid Aluminum Matrix Composites Reinforced with MWCNT Using Powder Metallurgy Process

Molecular Dynamics Simulation for the Analysis of Mechanical Properties and Effect of Stone-Wales and BiVacancy Defect on Carbon Nanotube Reinforced Iron Composites

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Reinforcing Iron Metal Matrix Composite by Multi-Wall Carbon Nanotube: A Combined Theoretical and Computational Approach

Enhanced physical and mechanical properties of Cu-based nanocomposites with bundled multi-layered carbon nanotubes incorporation: fabrication and comparative analysis via conventional sintering and SPS techniques

Development and characterization of multiwalled carbon nanotube-reinforced microwave sintered hybrid aluminum metal matrix composites: An experimental investigation on mechanical and tribological performances

The Influence of the Modification of Carbon Nanotubes on the Properties of Copper Matrix Sintered Materials

Effect of Increasing the Strength of Aluminum Matrix Nanocomposites Reinforced with Microadditions of Multiwalled Carbon Nanotubes Coated with TiC Nanoparticles

Mechanical Effects of Carbon Nanotubes-Graphene Reinforced Aluminium Matrix Composites

A Powder Metallurgy Route to Fabricate CNT-reinforced Molybdenum-Hafnium-carbon Composites

Effect of Carbon Nanotubes as Reinforcement on the Mechanical Properties of Aluminum-Copper-Magnesium Alloy

Interfacial/intragranular reinforcement of titanium-matrix composites produced by a novel process involving core-shell structured powder

Effect of NH2-MWCNTs sprayed carbon fiber on the mechanical properties of carbon fiber reinforced polycarbonate composite for lightweight structural applications

Microstructural Evolution and Mechanical Properties of Carbon Nanotubes–reinforced TZM Composites Synthesized by Powder Metallurgy

On effect of particle size distribution on the elastic/plastic deformation of metal matrix composites

Effect of Carbon Fibre Reinforcement on an Aluminium Metal Matrix Composite Joint Through Upward Friction Stir Processing

Effect of Multi-Walled Carbon Nanotubes and Carbon Fiber Reinforcements on the Mechanical and Tribological Behavior of Hybrid Mg-AZ91D Nanocomposites

Microstructural evolution and performance analysis of WC-11Co reinforced iron matrix composites

Investigation of Microstructure and Strengthening Mechanism in CNTs Reinforced Mo-based Composites

Effect of Tungsten Carbide Additions on the Microstructure, Mechanical, and Tribological Properties of M2 High-Speed Steel Matrix Composites