Abstract:Conventional silicon (Si) wafers are produced by energy‐intensive ingot crystallization which is responsible for a major share of a solar cell's carbon footprint. Our work explores Si EpiWafers that are produced by direct epitaxial deposition of trichlorosilane on a re‐usable substrate. This approach requires less energy and material and hence offers a potential for reduced cost and carbon footprint. Solar cells made from EpiWafers usually suffer from efficiency losses due to recombination at structural crystal defects associated with epitaxial growth. We investigated the nature of these defects and observed that defects at the EpiWafer's back surface are critical. Most of these defects are highly recombination‐active, pairwise‐connected misfit dislocations in the ‐direction. They originate from a lattice mismatch between the highly‐doped substrate and the less‐doped epitaxially grown layer. In this contribution, we demonstrate that the detrimental impact of these defects can be mitigated using typical manufacturing processes of high‐efficiency solar cells, such as KOH‐etching, gettering and oxidation. We report local minority charge carrier lifetimes as high as 2.2 ms after industrially feasible processes. Simulations using efficiency limiting bulk recombination analysis (ELBA) imply that the material would allow conversion efficiencies of up to 25.6 % considering a TOPCoRE solar cell design. TOC: Epitaxially grown silicon wafers (EpiWafers) are a promising alternative to Cz‐Si wafers for highly efficient solar cells with a low carbon footprint. For p‐type EpiWafers, we report minority charge carrier lifetimes as high as 2.2 ms and an efficiency potential of 25.6 %. Structural defects, as a remaining quality limitation in the EpiWafer, are discussed with respect to the effect of KOH‐etching, gettering, and oxidation. This article is protected by copyright. All rights reserved.

Past, Present, and Future Outlook for Edge Isolation Processes in Highly Efficient Silicon Solar Cell Manufacturing

Solar cell Edge shunt isolation : A simplified approach

Simulation-based roadmap for the integration of poly-silicon on oxide contacts into screen-printed crystalline silicon solar cells

Suppressing The Blistering of Silicon Nitride in PERC Solar Cells for High Industrial Yield

Towards Highly Efficient Low Carbon Footprint Solar Cells: Impact of High Temperature Processing on Epitaxially Grown P‐Type Silicon Wafers

Industrial High Throughput Emitter Formation and Thermal Oxidation for Silicon Solar Cells by the High Temperature Stack Oxidation Approach

Stable passivation of cut edges in encapsulated n-type silicon solar cells using Nafion polymer

Industrial Silicon Solar Cells Applying the Passivated Emitter and Rear Cell (PERC) Concept—A Review

Mass production of crystalline silicon solar cells with polysilicon‐based passivating contacts: An industrial perspective

Interdigitated Back Contact Technology as Final Evolution for Industrial Crystalline Single-Junction Silicon Solar Cell

Thermal laser separation and high-throughput layer deposition for edge passivation for TOPCon shingle solar cells

Post-Separation Processing for Silicon Heterojunction Half Solar Cells With Passivated Edges

Both-Sided TOPCon Solar Cells – Towards a Lean Process Flow for Silicon Bottom Solar Cells

Wet-Chemically Grown Interfacial Oxide for Passivating Contacts Fabricated With an Industrial Inline Processing System

A Novel Processing Technology for High‐Efficiency Silicon Solar Cells

Postmetallization “Passivated Edge Technology” for Separated Silicon Solar Cells

Developing Screen-Printing Processes for Silver Electrodes Towards All-Solution Coating Processes for Solar Cells

Improved Surface Passivation by Wet Texturing, Ozone‐Based Cleaning, and Plasma‐Enhanced Chemical Vapor Deposition Processes for High‐Efficiency Silicon Heterojunction Solar Cells

Material and Process Tolerant High Efficiency Solar Cells with Dynamic Recovery of Performance

Improving the Surface Passivation and Cleaning Quality of c-Si Wafers for the Application of TOPCon Solar Cells

Industry related approaches for bifacial p-type PERX solar cells