Abstract:Pure copper is very soft, however, hardening the pure copper with most strengthening mechanisms leads to a significant reduction in electrical conductivity. Grain refinement is a better strengthening mechanism to maintain high enough electrical conductivity. Plastic deformation at room temperature followed by post-annealing is one of the best methods to achieve fine-grained metals and alloys. In this research, the high-temperature annealing behavior of cold-rolled electrolytic tough-pitch (ETP) copper sheets was studied. 90 % asymmetric cold rolling followed by high-temperature post-annealing at 673 K for 1, 2, 5, 10, 30, 60, and 120 min were applied on the copper. The microstructure was significantly changed with increasing annealing time from 1 to 2 min owing to full recrystallization. With increasing the annealing duration, the grain size is increased. The formation of equiaxed grains with a smaller size (∼9 μm) compared to the full-annealed (initial) sample (∼68 μm) is observed after the longest time of post-annealing (120 min) due to the pinning effect of Cu2O particles. The post-annealed copper sheets processed by asymmetric rolling (in this work) exhibited a more homogeneous microstructure through the thickness compared to the symmetric rolling due to more uniform stored strain energy. The results showed that the first deformed grains that undergo recrystallization during post-annealing are Goss-oriented grains. With an increase in the post-annealing time, the S and Copper components were eliminated and a strong Cube and P texture orientations were formed. Interestingly, after 1 min of post-annealing, the yield and tensile strength enhanced to 410.2 MPa and 418.6 MPa owing to the annealing hardening phenomenon. The hardness and strength reached a constant value after the post-annealing for 10 min and above. With increasing the post-annealing duration, the central area of fracture surfaces (consisting of ductile dimples) became larger and the outer region (consisting of flat surfaces and shear dimples) became smaller, showing a shift towards perfect ductile fracture. With the increase of post-annealing time from 1 min to 120 min, the electrical conductivity was increased from 77.6 to 97.5 %IACS. The presence of the Cube texture increased the electron mobility compared to the P orientation, by reducing the mean distance that they can travel without scatter. From the obtained results, it can be concluded that the asymmetric cold rolling followed by high-temperature post-annealing is capable of strength improvement and maintaining electrical conductivity in copper.

Effect of Alternating Bending on the Structure and Mechanical Properties of Tough-Pitch Copper

Mechanical and microstructural single-crystal Bauschinger effects: Observation of reversible plasticity in copper during bending

Strain hardening in bent copper foils

High-temperature annealing behavior of cold-rolled electrolytic tough-pitch copper

Microstructure and Bending Properties of Cu-Cr-Zr Alloy Subjected to Heat Treatment and Rolling

Effect of Stretch Bending on the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy

Low‐Temperature Annealing of Asymmetrically Cold‐Rolled Electrolytic Tough‐Pitch Copper: Anneal Hardening and Bimodal Microstructure

Bending Stress Relaxation of Microscale Single-Crystal Copper at Room Temperature: an in Situ SEM Study

Bending Properties and Deformation Micromechanisms of Near-Α Titanium Alloy Sheets/foils Considering Initial Texture Characteristics and Size Effect

High Strength and High Ductility Copper Obtained by Topologically Controlled Planar Heterogeneous Structures

EFFECT OF DIFFERENT STRAIN ROUTES ON MECHANICAL PROPERTIES AND MICROSTRUCTURE OF COPPER

Microstructure Evolution and Mechanical Behavior of AZ31 Magnesium Alloy Sheet with Bimodal Texture under Bending Deformation

Changes in Microstructure and Mechanical Properties of Steel-Copper Wire During Deformation

Experimental Study on Pure Copper Subjected to Different Severe Plastic Deformation Modes

Investigation of the Dendritic Structure Influence on the Electrical and Mechanical Properties Diversification of the Continuously Casted Copper Strand

Enhancement of Tensile Ductility and Stretch Formability of AZ31 Magnesium Alloy Sheet Processed by Cross-Wavy Bending

Bendability enhancement of an age-hardenable aluminum alloy: Part I — relationship between microstructure, plastic deformation and fracture

Bendability enhancement of an age-hardenable aluminum alloy: Part II — multiscale numerical modeling of shear banding and fracture

Thermal Annealing Effect on Elastoplastic Behaviour of Al/Cu Bimetal during Three-Point Bending

Texture evolution and its influence mechanism on properties of single crystal copper and polycrystalline copper during cumulative deformation

Effect of Initial Texture on the Bending Behavior, Microstructure and Texture Evolution of ZK60 Magnesium Alloy During the Bending Process