Abstract:This paper describes the main results from an experimental investigation into tailoring the phase content and grain structure for high strength of a microstructurally flexible high entropy alloy (HEA), Fe42Mn28Co10Cr15Si5 (in at%), using rolling, friction stir processing (FSP), and compression. Optical microscopy, neutron diffraction, and electron backscatter diffraction were employed to characterize microstructure and texture evolution. The material upon rolling was found to have triplex structure consisting of metastable gamma austenite (γ), stable sigma (σ), and stable epsilon martensite (ε) phases. The adaptive phase stability exhibited by the selected HEA of very low stacking fault energy with strain, strain rate, and temperature was used along with grain refinement to enhance the strength. To this end, the complex structure was refined by FSP at 350 revolutions per minute (RPM) tool rotation rate, while increasing the fraction of γ and decreasing the σ and ε content. The strength was further enhanced by FSP at 150 RPM by further refinement of the grain structure and increasing the fraction of ε phase. The peak ultimate tensile strength of ~1850 MPa was achieved by double pass FSP (350 RPM followed by 150 RPM), the sequence which even more refined the microstructure and increased the fraction of σ phase. While the content of diffusion created σ phase remains constant during subsequent compression, the fraction of ε increases due to the diffusionless strain induced γ→ε phase transformation. The transformation facilitates plastic strain accommodation and rapid strain hardening, which has been attributed to the increase in highly dislocated ε phase fraction and transformation induced dynamic Hall-Petch-type barrier effect. Interestingly, a great deal of hardening ability was exhibited by the HEA even at very high strength. Roles of texture, grain size, and phase content on the transformation during compression have been rationalized and discussed in this paper.

Bendability enhancement of an age-hardenable aluminum alloy: Part II — multiscale numerical modeling of shear banding and fracture

Bendability enhancement of an age-hardenable aluminum alloy: Part I — relationship between microstructure, plastic deformation and fracture

Experimental and numerical investigation of failure during bending of AA6061 aluminum alloy sheet using the modified Mohr-Coulomb fracture criterion

Influence of ductile damage on the bending behaviour of aluminium alloy thin sheets

Crystal Plasticity Finite Element Analyses on the Formability of AA6061 Aluminum Alloy with Different Ageing Treatments

Phase-Field Modeling of Coupled Brittle-Ductile Fracture in Aluminum Alloys

Experimental and numerical investigation on plasticity and fracture behaviors of aluminum alloy 6061-T6 extrusions

An innovation in finite element simulation via crystal plasticity assessment of grain morphology effect on sheet metal formability

Characterization and constitutive analysis-based crystal plasticity of warm flow and fracture behaviours of 2060 Al-Cu-Li alloy

Evolution of the Texture and Mechanical Properties of 2060 Alloy During Bending

Strain Localization and Damage Development in 2060 Alloy During Bending

Anisotropic microstructures and mechanical properties of textured Ti3AlC2/TiAl3/Al composite

Experimental and numerical studies on bending characteristics of woven CFRP reinforced aluminum thin-walled automotive structures

Prediction of failure in bending of an aluminium sheet alloy

An integrated computational and experimental study of the failure mode in Mg/Al laminated composite under three-point bending

A continuum damage model for Mg/Al composite sheets rolling: Theoretical development and application

Experiment and multiscale modeling of the coupled influence of constituents and precipitates on the ductile fracture of heat-treatable aluminum alloys

Effects of plasticity-induced martensitic transformation and grain refinement on the evolution of microstructure and mechanical properties of a metastable high entropy alloy

Theoretical modeling of toughening mechanisms in the CrMnFeCoNi high-entropy alloy at room temperature

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

A Damage-Effect-involved Phenomenological Crystal Plasticity Model and Computational Methods for Mechanical Responses of FeCrAl Alloys